Jiri Navratil

Jiri Navratil

Auto-generated profile, based on publicly available information

Jiri Navratil

University of West Bohemia,Faculty of Electrical Engineering,Pilsen,Czech Republic

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 September 2001
Verified
Conference Paper
Closed access
JNJiri Navratil
Jiri Navratil
UCUpendra V. Chaudhari
Upendra V. Chaudhari
GRGanesh N. Ramaswamy
Ganesh N. Ramaswamy

1 May 2020
Verified
Conference Paper
Closed access
Martin HirmanMartin Hirman
Martin Hirman
JNJiri Navratil
Jiri Navratil
FSFrantišek Steiner
František Steiner
AHAles Hamacek
Ales Hamacek
The paper deals with temperature ageing reliability of joints glued by non-conductive adhesive (NCA) onto the conductive ribbon. The samples prepared with NCA were accelerated aged at 85 °C temperature for 1000 hours. The samples were also stretched on 150 % of their relaxed length during the ageing. The main aim of the experiment was to verify the possibility of NCA using to make a conductive connection of components onto the ribbon. The joints electrical resistance was measured before, during and after ageing. The results show that using this technology for standard use of ribbons is suitable and reliable.

1 May 2017
Verified
Conference Paper
Closed access
JNJiri Navratil
Jiri Navratil
MPMartin Pavec
Martin Pavec
JRJan Reboun
Jan Reboun
TRTomas Rericha
Tomas Rericha
AHAles Hamacek
Ales Hamacek
This paper presents a research focused on Aerosol Jet printed lines on subsequently bent glass substrates. The thin glass rods were used as the glass substrates. Three different patterns were printed by silver nanoparticle ink on the thin rods and the ink was sintered. The thin rods were bent in a flame in different angles after the ink sintering. The resistivity was measured before and after the bending and also the microscopic observation was realized in order to discover which of the printed patterns is the best for bending.

1 September 2003
Verified
Conference Paper
Closed access
RZRan D. Zilca
Ran D. Zilca
JNJiri Navratil
Jiri Navratil
GRGanesh N. Ramaswamy
Ganesh N. Ramaswamy

1 May 2019
Verified
Conference Paper
Closed access
MPMartin Pavec
Martin Pavec
JNJiri Navratil
Jiri Navratil
RSRadek Soukup
Radek Soukup
VSVaclav Smitka
Vaclav Smitka
AHAles Hamacek
Ales Hamacek
This paper presents research focused on the development of a flexible fully printed IoT antenna for a drone-deployed autonomous sensor unit optimized for IoT applications. Aerosol Jet® was chosen as manufacturing technology. DuPont™ Kapton® HN 500 polyimide foil was used as a substrate. Conductive silver nanoparticle ink Clariant Prelect TPS50 was used for printing the antenna. Antennas were prepared with the different number of printed layers. A demonstrator with the fully printed flexible antenna was fabricated by Aerosol Jet printing technology and tested.

3 September 2024
Verified
Conference Paper
Closed access
Martin HirmanMartin Hirman
Martin Hirman
KSKrystof Svagr
Krystof Svagr
JNJiri Navratil
Jiri Navratil
David KalašDavid Kalaš
David Kalaš
FSFrantišek Steiner
František Steiner
This paper deals with the reliability of conductive joints between components and textile ribbons in salty environment. In the experiment three different contacting methods (low temperature soldering, non-conductive adhesive bonding, thermocompression bonding) were used. The experiment showed that in case of non-conductive adhesive bonding method, the viscosity of adhesive is crucial and samples with high viscosity adhesive are not applicable. The experiment also showed that low temperature soldering, non-conductive adhesive bonding using a suitable non-conductive adhesive or thermocompression method with the using of a conductive filament can be recommended and joints prepared by these methods are practically applicable in salty environment.