Perturbation-based gait assessment has been used to quantify gait stability in older adults. However, knowledge on which perturbation type is most suitable to identify poor gait stability is lacking. We evaluated the effects of ipsi- and contra-lateral sway, belt acceleration and deceleration, and visual and auditory perturbations on medio-lateral (ML) and anterior-posterior (AP) margins of stability (MoS) in young and older adults. We aimed to evaluate (1) which perturbation type disturbed the gait pattern substantially, (2) how participants recovered, and (3) whether recovery responses could discriminate between young and older adults. Nine young (25.1 ± 3.4 years) and nine older (70.1 ± 7.6 years) adults walked on the CAREN Extended (Motek BV, The Netherlands). The perturbation effect was quantified by deviation in MoS over six post-perturbation steps compared to baseline walking. Contra-lateral sway and deceleration perturbations resulted in the largest ML (1.9–4 times larger than other types) and AP (1.6–5.6 times larger than other types) perturbation effects, respectively. After both perturbation types, participants increased MoS by taking wider, shorter, and faster steps. No differences between young and older adults were found. We suggest to evaluate the potential of using contra-lateral sway and deceleration perturbations for fall risk identification by including both healthy and frail older adults.
To maximise the efficiency of gait interventions, gait phase and joint kinematics are important for closing the system loop of adaptive robotic control. However, few studies have applied an inertial sensor system including both gait phase detection and joint kinematic measurement. Many algorithms for joint measurement require careful alignment of the inertial measurement unit (IMU) to the body segment. In this paper, we propose a practical gait feedback method, which provides sufficient feedback without requiring precise alignment of the IMUs. The method incorporates a two-layer model to realise simultaneous gait stance and swing phase detection and ankle joint angle measurement. Recognition of gait phases is performed by a high-level probabilistic method using angular rate from the sensor attached to the shank while the ankle angle is calculated using a data fusion algorithm based on the complementary filter and sensor-to-segment calibration. The online performance of the algorithm was experimentally validated when 10 able-bodied participants walked on the treadmill with three different speeds. The outputs were compared to the ones measured by an optical motion analysis system. The results showed that the IMU-based algorithm achieved a good accuracy of the gait phase recognition (above 95%) with a short delay response below 20 ms and accurate angle measurements with root mean square errors below 3.5° compared to the optical reference. It demonstrates that our method can be used to provide gait feedback for the correction of drop foot.
1 June 2015 in Proceedings of the Institution of Civil Engineers - Municipal Engineer
Horizontal and vertical gaps between the train and the platform are a major safety concern for railway passengers, especially for disabled passengers. London Underground is implementing a programme to install platform humps to remove vertical differences between the train and the platform. In order to properly design platform humps, this study empirically investigated the effects of the design factors of the ramps, namely the slope and cross-fall gradients, on disabled passengers. The investigation consisted of two experiments: one where 20 participants were asked to walk on simulated slopes, and the other where 25 participants were asked to board or alight from the simulated train from or onto the slopes. The slope gradients tested were 3·0% (1:33), 5·2% (1:19) and 6·9% (1:14) with the cross-fall gradients 1·5% (1:67), 2·0% (1:50) and 2·5% (1:40). The results showed that the slope gradient does not largely affect the participants' performance of longitudinal walking on the slopes or their subjective safety evaluation, but would cause additional difficulty for them to board/alight from the train from/onto the slope. This suggests that train doors should not stop next to the ramp. There was little evidence concerning the effects of the cross-fall gradient. The results provide useful information for designing platform humps.
Functional methods identify joint centres as the centre of rotation (CoR) of two adjacent movements during an ad-hoc movement. The methods have been used for functionally determining hip joint centre in gait analysis and have revealed advantages compared to predictive regression techniques. However, the current implementation of functional methods hinders its application in clinical use when subjects have difficulties performing multi-plane movements over the required range. In this study, we systematically investigated whether functional methods can be used to localise the CoR during a quasi-planar movement. The effects of the following factors were analysed: the algorithms, the range and speed of the movement, marker cluster location, marker cluster size and distance to the joint centre. A mechanical linkage was used in our study to isolate the factors of interest and give insight to variation in implementation of functional methods. Our results showed the algorithms and cluster locations significantly affected the estimate results. For all algorithms, a significantly positive relationship between CoR errors and the distance of proximal cluster coordinate location to the joint centre along the medial-lateral direction was observed while the distal marker clusters were best located as close as possible to the joint centre. By optimising the analytical and experimental factors, the transformation algorithms achieved a root mean square error (RMSE) of 5.3 mm while the sphere fitting methods yielded the best estimation with an RMSE of 2.6 mm. The transformation algorithms performed better in presence of random noise and simulated soft tissue artefacts.
16 June 2020 in Computer Methods in Biomechanics and Biomedical Engineering
A major source of error in reliability of gait analysis arises from the palpation of anatomical landmarks (ALs). The purpose of this study was to investigate whether less reliance on manually identifying ALs could improve inter-assessor reliability of joint kinematics compared to two anatomical models. It was hypothesised that the Strathclyde functional cluster model (SFCM), in which the hip, knee and ankle joint centres and knee and ankle flexion axes were determined by functional methods, would obtain greater inter-assessor reliability. Ten able-bodied participants and seven assessors were recruited. Each participant completed three trials conducted by different assessors on non-consecutive days. Agreement and inter-assessor reliability between the models were compared and analysed, whilst factor effects of assessor experience and body mass index (BMI) were investigated. The SFCM obtained excellent agreement with anatomical models for all sagittal angles and hip ab/adduction angle, and it showed slightly higher inter-assessor reliability with smaller variations in the knee and ankle. The assessor experience was not a significant factor, but the BMI had a significant effect on the inter-assessor reliability. The results demonstrate that the SFCM may be more beneficial for less experienced assessors.