20 December 2021 in Jurnal Teknik Elektro
In a power plant such as micro-hydropower (MHP), an induction generator (IG) is usually employed to produce electrical power. Therefore, an inverter is needed to deliver it with high efficiency. Z-source inverter (ZSI) has been introduced as a topology with many advantages over conventional inverters. This research aims to investigate the performance of ZSI based simple boost control (SBC) in laboratory-scale MHP systems using a rewinding induction generator. This research has been conducted both from simulations and experiments. Based on the result, the waveform characteristic and value of ZSI are close to the desired design. A shoot-through duty ratio of 17% can reach 60 Vrms output voltage, and this condition has a conversion ratio of about 2.05 times. Also, SBC can significantly reduce the Total Harmonic Distortion (THD). ZSI efficiency has a value of 84.78% at 50% of rating load 100 W and an average value of 80%. Compared to the previous study, the proposed design has more economical with the same component for the higher rating power. Moreover, it has a smoother and entire output waveform of the voltage.
19 July 2022 in BULETIN OSEANOGRAFI MARINA
MWMuhammad Khaisar Wirawan
+1
Pembangunan Dermaga C sebagai fasilitas baru di PT Petrokimia Gresik bertujuan untuk meningkatkan produktivitas perusahaan. Produktivitas ini terwujud dalam bentuk aktivitas percepatan bongkar muat barang yang diangkut dari kapal ke daratan atau sebaliknya. Namun, aktivitas ini akan terkendala di masa depan jika sedimentasi tidak diatasi dengan baik. Untuk mengatasi fenomena sedimentasi di suatu dermaga, perlu dilakukan analisis laju sedimentasi secara dini dengan mempertimbangkan faktor-faktor seperti karakteristik pasang surut, pola arus, dan profil gelombang. Beberapa cara dapat dilakukan untuk meminimalisir laju sedimentasi, salah satunya dengan memodifikasi layout dermaga dengan tujuan untuk mengurangi frekuensi pengerukan. Penelitian ini bertujuan untuk menganalisis laju sedimentasi di sekitar Dermaga C dan menghitung perkiraan volumenya. Dua layout alternatif dari Dermaga C eksisting diusulkan untuk meminimalisir bed level thickness yang dapat terjadi di dermaga. Penelitian ini menerapkan pemodelan numerik berbasis software MIKE 21. Hasilnya, layout alternatif 1 dan 2 untuk periode yang sama mampu mengurangi volume sedimentasi terhadap layout eksisting masing-masing sebesar 9348.12 m3 dan 13215.48 m3 atau memiliki persentase penurunan sebesar 45.3% dan 64.1%. Di antara layout alternatif 1 (LA1) dan 2 (LA2), layout kedua adalah rekomendasi yang paling optimal. Oleh karena itu, dapat disimpulkan bahwa modifikasi layout terbukti dapat menurunkan laju sedimentasi di Dermaga C. Construction of Port C as a new facility at PT Petrokimia Gresik aims to increase the company's productivity. This productivity is manifested in accelerating the loading and unloading of materials transported from ships to land or vice versa. However, this activity will be hampered in the future if the sedimentation is not handled correctly. Hence, the sedimentation phenomenon in a port needs to be overcome. It is essential to investigate the sedimentation rate by considering tidal characteristics, current patterns, and wave profiles. Various ways can be conducted to decrease the sedimentation rate, one of which is by modifying the port layout to minimize the intensity of dredging. This research aims to analyze the sedimentation rate around Port C and calculate the estimated volume. Two alternative layouts are proposed to minimize the bed level thickness on the Port C. This research applies numerical modeling based on MIKE 21 software. As a result, alternative layouts 1 and 2 for the same period can reduce the sedimentation volume to the existing layout by 9348.12 m3 and 13215.48 m3, respectively, or have a decreasing percentage of 45.3% and 64.1. %. The last layout is the most significant among alternative layouts 1 (LA1) and 2 (LA2). It can be emphasized that the layout modification is proven to decrease the sedimentation rate at Port C.
15 July 2022 in Jurnal Kelautan Nasional
Turbin tipe Darrieus merupakan salah satu jenis turbin sumbu vertikal yang memiliki prospek menjanjikan dalam pengembangan turbin hidrokinetik, salah satunya dalam aplikasi untuk pembangkit arus laut. Berbagai penelitian telah dilakukan untuk meningkatkan performa turbin Darrieus yang pada umumnya memiliki performa efisiensi dan self-starting lebih rendah dibandingkan jenis turbin sumbu horisontal. Tujuan penelitian ini adalah untuk mengevaluasi performa turbin Darrieus yang ditinjau dari aspek efisiensi dan kemampuan self-starting. Skenario pengujian berupa penerapan bentuk foil dan blade swept angle (γ) pada desain turbin dipertimbangkan dalam penelitian ini. Pada evaluasi pengaruh bentuk foil, diterapkan foil NACA 634021 sebagai foil utama kemudian dibandingkan dengan foil lain seperti NACA 0018. Sedangkan evaluasi pengaruh blade swept angle, dipertimbangkan nilai γ = 30° agar menghasilkan turbin dengan bentuk V-shaped blade yang kemudian dibandingkan dengan turbin Straight blade dengan γ = 0°. Software QBlade digunakan untuk mensimulasikan turbin V-shaped blade selama kondisi kerja. Hasil simulasi menunjukkan bahwa turbin V-shaped blade yang berbasis foil NACA 634021 mampu mencapai efisiensi terbesar yaitu 0,425 dan memiliki self-starting yang baik pada cut-in speed arus laut sebesar 1,765 m/s. Selain itu, turbin ini juga mampu menghasilkan daya sebesar 27,64 kW pada kecepatan ratingnya dengan rata-rata peningkatan daya tiap 1 m/s arus laut sebesar 2,51 kW.
7 February 2023 in Jurnal Teknologi
The V-shaped blade turbine is one of the turbine models with good self-starting capability, although its efficiency is still standard. Various studies, especially of foil shape and blade swept angle variations applied to V-shaped blade turbines, have been carried out to improve its performance. This study aims to optimize the ability of a V-shaped blade turbine in terms of efficiency and self-starting by investigating the effect of blade aspect ratio and solidity through several test scenarios. NACA 634021 foil and a blade swept angle of 30° were used to create the main form of a V-shaped blade turbine. The simulation results using the QBlade software show that the blade aspect ratio and solidity significantly affect the efficiency and self-starting capability of the V-shaped blade turbine. Finally, the optimal design configuration was achieved on the turbine dimensions with a height of 3.1344 m, a radius of 1.8288 m, a chord foil length of 0.2134 m, and a total of four blades. This configuration can achieve maximum efficiency of 0.441 and fulfills self-starting at the minimum tip speed ratio limit of 0.7.
1 June 2026 in International Journal of Applied Power Engineering (IJAPE)
Small-scale wind turbines (SSWT) encounter a primary issue in power extraction, making the integration of DC-DC converters with maximum power point tracking (MPPT) crucial for performance enhancement. This study focuses on an evaluation of basic DC-DC converters, which offer many benefits when applied to SSWT systems. By considering efficiency, suitability, and electrical stress aspects, six DC-DC converter topologies consisting of boost, buck-boost, SEPIC, Cuk, zeta, and Luo, were tested under perturb and observe (P&O) and incremental conductance (INC) MPPT strategies. A 6.5-kW SSWT system, including a DC-DC converter and MPPT was designed in detail using PSIM. The results show that boost converter demonstrated the best overall performance in terms of power extraction, efficiency, and stress reduction, although its operation was limited to a narrower wind speed range. The zeta converter achieved efficiency and power extraction comparable to the boost converter with stable operation over a broader wind speed range, while the buck–boost converter offered step-up/step-down capability but experienced higher voltage and current stress. The SEPIC and Cuk converters showed low overall performance compared to others, whereas the Luo converter was better suited for low-wind-speed conditions.