22 November 2021 in IEEE Photonics Journal
In this work, we fabricated and characterized 4 × 4 parallel flip-chip AlGaN-based micro-LED arrays with varied mesa diameters of 120 µm, 100 µm, 80 µm, and 60 µm. The reported micro-LED arrays have a maximum bandwidth of 380 MHz and a peak wavelength of ∼275 nm. It is found that the electrical and optical characteristics of AlGaN-based micro-LED arrays show strong size dependence for ultraviolet communication (UVC). The differential resistance increases from 28.8 Ω to 112 Ω, the external quantum efficiency (EQE) is increased by ∼30%, and the bandwidth doubles as the diameter of individual micro-LED decreases from 120 µm to 60 µm. Our research proves that tailoring the mesa size of parallel flip-chip AlGaN-based micro-LED arrays can further enhance its bandwidth and promote its application in UVC.
19 April 2019 in Optics Letters
We report on the high-performance nanoporous (NP) GaN-based metal-insulator-semiconductor (MIS) ultraviolet (UV) photodetectors (PDs) with a thermal oxidized insulating layer. The devices show a high responsivity of and maximum external quantum efficiency of at 360 nm under a 10 V applied bias, which are attributed to the trap-assisted tunneling induced internal gain mechanism. Correspondingly, a specific detectivity of Jones and excellent optical switching repeatability are also observed in our fabricated PDs. The MIS UV PD may act as an excellent candidate for the application in UV photodetection due to the high performance and simple fabrication process.
30 July 2024 in Macromolecular Bioscience
Alginate (Alg) polymers have received much attention due to the mild conditions required for gel formation and their good bio‐acceptability. However, due to limited interactions with cells, many drugs, and biomolecules, chemically modified alginates are of great interest. Sulfated alginate (S–Alg) is a promising heparin‐mimetic that continues to be investigated both as a drug molecule and as a component of biomaterials. Herein, the S–Alg literature of the past five years (2017–2023) is reviewed. Several methods used to synthesize S–Alg are described, with a focus on new advances in characterization and stereoselectivity. Material fabrication is another focus and spans bulk materials, particles, scaffolds, coatings, and part of multicomponent biomaterials. The new application of S–Alg as an antitumor agent is highlighted together with studies evaluating safety and biodistribution. The high binding affinity of S–Alg for various drugs and heparin‐binding proteins is exploited extensively in biomaterial design to tune the encapsulation and release of these agents and this aspect is covered in detail. Recommondations include publishing key material properties to allow reproducibility, careful selection of appropriate sulfation strategies, the use of cross–linking strategies other than ionic cross–linking for material fabrication, and more detailed toxicity and biodistribution studies to inform future work.
1 February 2012 in Materials Science in Semiconductor Processing
5 September 2025 in Journal of Materials Chemistry B
Surface modification of poly(ε-caprolactone) (PCL) to facilitate interactions with high pI proteins is a strategy used to enhance 3D PCL scaffolds for tissue engineering applications. The approach of the current study was to firstly optimise the surface modification on 2D films and then apply to 3D scaffolds. Melt-pressed PCL films were grafted with 2-aminoethyl methacrylate via gamma radiation induced grafting to introduce amine functional groups to the substrate surfaces. The effect of different grafting conditions including monomer concentration, radiation dose, solvent and solution pH on the degree of grafting was evaluated using contact angle measurements and X-ray photoelectron spectroscopy. The optimised grafting conditions ensured the grafts had a hydrodynamic radius of <5 nm to allow clearance from the body after degradation of the PCL material. Solution binding studies of the polymers alginate, sulfated alginate (S-Alg), and heparin with the high pI heparin binding protein, lactoferrin (LF) confirmed that S-Alg is an effective heparin mimetic. This biopolymer was selected for conjugation to the amine-grafted PCL films through carbodiimide chemistry and time-of-flight secondary ion mass spectrometry was used to verify amide coupling. The stability of the surface layer was evaluated in vitro in buffer solution to determine that the unaltered and functional lifetime of the surface layer was at least 21 days. Binding of LF to the S-Alg modified surface was confirmed. The optimised amine grafting and S-Alg conjugation conditions were applied to 3D-printed medical-grade PCL scaffolds to demonstrate the potential clinical translation of this work.