Vladimir Milosavljevic

Vladimir Milosavljevic

Auto-generated profile, based on publicly available information

Vladimir Milosavljevic

School of Physical Science, Dublin City University, Dublin 8, Ireland

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2015 in Progress of Theoretical and Experimental Physics
Verified
Journal Article
Open access
PDF file
PCPJ Cullen
PJ Cullen
VMV. Milosavljević
V. Milosavljević
This study includes a detailed experimental investigation of the spatial and temporal spectroscopic emission of an argon plasma jet discharge. The study is carried out in ambient air and quenching by inflowing air species is considered. The optical emission spectroscopy of neutral atomic spectral lines and molecular bands, over a range of plasma process parameters, is investigated. Wavelength-resolved argon optical emission profiles are used to monitor the electron energy distribution function and the density of argon metastable atoms. The experimental data indicates that the argon flow rate, in a confined open-air plasma discharge, limits the impact of molecular oxygen in the creation of oxygen radicals. The absolute calibrated emission spectra facilitate the possibility of standardization of the so-called plasma dose.

13 August 2013 in Plasma Chemistry and Plasma Processing
Verified
Journal Article
Closed access
PDF file
MDMick Donegan
Mick Donegan
VMVladimir Milosavljević
Vladimir Milosavljević
Denis DowlingDenis Dowling
Denis Dowling

10 October 2018 in Materials
Verified
Journal Article
Open access
PDF file
LSLaurence Scally
Laurence Scally
MGMiroslav Gulan
Miroslav Gulan
LWLars Weigang
Lars Weigang
PCPJ Cullen
PJ Cullen
VMVladimir Milosavljevic
Vladimir Milosavljevic
The use of plastics has spanned across almost all aspects of day to day life. Although their uses are invaluable, they contribute to the generation of a lot of waste products that end up in the environment and end up polluting natural habitats such as forests and the ocean. By treating low-density polyethylene (LDPE) samples with non-thermal plasma in ambient air and with an addition of ≈4% CO2, the biodegradation of the samples can be increased due to an increase in oxidative species causing better cell adhesion and acceptance on the polymer sample surface. It was, however, found that the use of this slight addition of CO2 aided in the biodegradation of the LDPE samples more than with solely ambient air as the carbon bonds measured from Raman spectroscopy were seen to decrease even more with this change in gas composition and chemistry. The results show that the largest increase of polymer degradation occurs when a voltage of 32 kV is applied over 300 s and with a mixture of ambient air and CO2 in the ratio 25:1.

15 July 2014 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
Denis DowlingDenis Dowling
Denis Dowling
MDMick Donegan
Mick Donegan
PCPJ Cullen
PJ Cullen
VLVictor J. Law
Victor J. Law
VMVladimir Milosavljevic
Vladimir Milosavljevic
Atmospheric pressure plasma systems are routinely used to treat the surfaces of thermally sensitive materials. There are wide ranges of commercial plasma jet systems available, and for the end user, it can be difficult to directly compare the power outputs of these sources. This paper evaluates the use of a thermal imaging technique in order to provide a semiquantitative evaluation of energy output from plasma jets. The evaluation involved a comparison of the thermal energy transfer obtained from three commercially available atmospheric pressure plasma jet systems: 1) PlasmaTreat's Openair; 2) Dow Corning's PlasmaStream; and 3) SurFx's Atomflo.

13 March 2017 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Closed access
LSLaurence Scally
Laurence Scally
JLJames Lalor
James Lalor
PCPatrick J. Cullen
Patrick J. Cullen
VMVladimir Milosavljević
Vladimir Milosavljević
Due to the attraction of plasma technologies as a clean and efficient means of surface modification, significant research has gone into the physical and chemical aspects of polymer functionalization. In this study, it was shown that the use of an atmospheric plasma jet can efficiently modify the surface of polyethylene terephthalate samples and change their hydrophobic properties to more hydrophilic characteristics. The dependence on the changes with respect to time, distance, and atomic oxygen (O I) intensity were considered as factors. It was found that with closer proximity to the plasma source (without causing thermal degradation) and with increasing levels of O I, that the changes of water contact angle and surface free energy can be maximized. It was also observed that the electron energy distribution function, for a given chemistry, significantly differed with changes in distance from the jet nozzle. This shows that for this type of plasma jet system, the bulk of the chemical reactions occur in the nozzle of the jet and not in the surrounding atmosphere. Therefore, this leads to more efficient energy transfer, higher gas temperatures, and better surface activation of samples when compared to systems that produce external chemical reactions due to more diffusion in the surrounding atmosphere and loss of reactive species to other atoms and molecules that are present.