Gilles Dessein

Gilles Dessein

Auto-generated profile, based on publicly available information

Gilles Dessein

Department of Mechanical Engineering, Universitat Politècnica de Catalunya, 08019 Barcelona, Spain

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 December 2011 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
EMEl Bechir Msaddek
El Bechir Msaddek
ZBZied BOUAZIZ
Zied BOUAZIZ
Gilles DesseinGilles Dessein
Gilles Dessein
MBMaher BAILI
Maher BAILI
Our two major concerns, which should be taken into consideration as soon as we start the selecting the machining parameters, are the minimization of the machining time and the maintaining of the high-speed machining machine in good state. The manufacturing strategy is one of the parameters which practically influences the time of the different geometrical forms manufacturing, as well as the machine itself. In this article, we propose an optimization methodology of the machining strategy for pockets of complex forms. For doing this, we have developed analytic models expressing the feed rate of the cutting tools trajectory. Then, we have elaborated an optimization method based on the analysis of the different critical parameters so as to distinguish the most suitable strategies to calculate the cutting time and define the machine dynamics. To validate our results, we have compared them to the experimental ones and also to those found in literature.

12 August 2023 in Materials
Verified
Journal Article
Open access
PDF file
Gilles DesseinGilles Dessein
Gilles Dessein
WVWAGNER Vincent
WAGNER Vincent
Ramón Jerez-MesaRamón Jerez-Mesa
Ramón Jerez-Mesa
JLJordi Llumà
Jordi Llumà
J. Antonio Travieso-RodriguezJ. Antonio Travieso-Rodriguez
J. Antonio Travieso-Rodriguez
Gilles DesseinGilles Dessein
Gilles Dessein
In this study, we analyzed the effects of vibration assistance, combined with a ball burnishing process, in terms of topology, residual stresses, and tribological properties on 316L shafts. The burnishing variables consisted of the variation of the input force, the number of passes, and the activation of the vibration assistance, which is based on a 40 kHz frequency and 8 μm of vibration amplitude, derived in a screening design of three factors. The results show that the medium–high level of burnishing force, high level of the number of passes, and the activation of the vibration assistance are the best options in order to improve the average roughness, the microstructure, the increase in the compressive residual stresses, and the wear enhancement, besides all variables being significant in the p-value analysis through ANOVA. Statistically, the vibration-assisted ball burnishing improved the average roughness by 2.9%, enlarged the von Mises stress on the surface by 11.5% and enhanced the wear resistance of a 316L shaft and WC-Co ball contact up to 7.3%.

1 February 2023 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
EVEric Velázquez-Corral
Eric Velázquez-Corral
WVWAGNER Vincent
WAGNER Vincent
Ramón Jerez-MesaRamón Jerez-Mesa
Ramón Jerez-Mesa
Karl DelbéKarl Delbé
Karl Delbé
JLJordi Llumà
Jordi Llumà
Gilles DesseinGilles Dessein
Gilles Dessein
The objective of the research is to analyze the impact of the ultrasonic vibration assistance on the wear resistance due to the topography enhancement caused on Ti6Al4V cylindrical samples after surface modification through a ball burnishing process. The process parameters considered for this study are the burnishing force, the number of passes, and the addition of a 40 kHz ultrasonic assistance, which are thought to enhance the surface topography and increase the hardener effect in terms of depth. A complete screening design of 3 factors was performed, revealing that the number of passes and the vibration assistance are the most important parameters for minimizing the wear volume loss, being 170 N of burnishing force, 3 passes, and the addition of the vibration assistance as the best combination found. However, no significant difference in the friction force was observed. The topography results show that there is a decrease in the average roughness from 1.50 to 0.45 μm with optimal burnishing conditions. It was also analyzed the microstructure originated after the turning, the conventional ball burnishing, and the vibration-assisted ball burnishing, being the last optimal in terms of depth affectation to the microstructure. Therefore, these results confirm an improvement in terms of wear enhancement, friction reduction, and topography results when vibration assistance is added to a conventional ball burnishing process.

14 February 2018 in Machining Science and Technology
Verified
Journal Article
Closed access
OSOleksii Shtehin
Oleksii Shtehin
SSSébastien Seguy
Sébastien Seguy
VWVincent Wagner
Vincent Wagner
Yann LandonYann Landon
Yann Landon
Gilles DesseinGilles Dessein
Gilles Dessein
MMMichel Mousseigne
Michel Mousseigne
In this study low-frequency chatter during machining of inclined surfaces with ball-end mills is experimentally investigated. An explanation of genesis of low-frequency vibrations have been proposed for various conditions: cutting direction, lead angle values, spindle speed, depth of cut. As a result, it has been proven that low-frequency chatter has more significant effect on machined surface than usual chatter. Low-frequency chatter occurs during downward milling, rather than upward milling, especially when lead angle increases. Furthermore, low-frequency chatter takes place in the beginning of cutting process, thereafter develops into steady state of usual chatter, which has no such significant effect on machined surface, as it has been shown. The results are in line with the supposition that low frequency vibrations are caused by sudden and irregular nature of shearing process, when magnitude is small.