Cathodic protection was introduced two centuries ago and since has found widespread application in protecting structures such as pipelines, offshore installations, and bridges from corrosion. Despite its extensive use, the fundamental working mechanism of cathodic protection remains debated, particularly for metals in porous media such as soil. Here, we use in-situ and ex-situ characterisation techniques coupled with electrochemical measurements to characterise the spatio-temporal changes occurring at the steel-electrolyte interface. We show that upon cathodic protection, the interfacial electrolyte undergoes alkalinisation and deoxygenation, and that depending on polarisation conditions, an iron oxide film can simultaneously form on the steel surface. We further demonstrate that these changes in interfacial electrolyte chemistry and steel surface state result in altered anodic and cathodic reactions and their kinetics. We propose a mechanism of cathodic protection that integrates previous theories, based on both concentration and activation polarisation, complimentarily. We discuss the implications of this study in enhancing corrosion protection technologies and the safe, economical, and environmentally friendly operation of critical steel-based infrastructures.
25 March 2022 in Corrosion Engineering, Science and Technology: The International Journal of Corrosion Processes and Corrosion Control
Electrical resistance (ER) probes are a technique used to monitor the corrosion rate (CR) of metals in a wide range of applications and industries. However, limited data comparing CR measured with ER-probes, weight loss and electrochemical methods is available. The aim of this work is to provide data regarding the reliability of CR measurements with ER-probes by comparison with LPR, EIS and weight loss measurements and to provide suggestions for designing ER-probes depending on the expected corrosion mechanism and CR. To evaluate the ER-probes reliability in CR measurements, both uniform and localised corrosion in four different environments were studied. CRs obtained with ER-probes showed good agreement with weight loss and electrochemical measurements. Numerical models were used to optimise ER-probe geometry regarding the expected corrosion type and CR, and to study the effect of Joule heating. Design charts were proposed to support ER-probes design concerning the expected CR in certain applications.
1 January 2020 in Journal of the Electrochemical Society
The corrosion behavior of carbon steel was investigated in deaerated, moderately alkaline conditions (pH 9.8) at room temperature. This study was mainly focused on the influences of carbonate and bicarbonate ions, exposure time, and scale formation on the corrosion rate. The corrosion rate was calculated from Linear Polarization Resistance (LPR) measurements, Electrochemical Impedance Spectroscopy (EIS), analyzing Potentiodynamic Polarization (PDP) curves, and based on time-resolved dissolved iron concentration measurements through Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). Surface characterization of corrosion products was performed by means of Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray analysis (EDX). The results showed that the presence of carbonate and bicarbonate significantly modified the corrosion behavior of the steel electrodes and gave rise to corrosion rates of several hundreds of μ m y −1 , over time decreasing to levels around 100–200 μ m y −1 . This decrease in corrosion rate was related to scale formation that introduced a certain degree of mass transport limitations. Nevertheless, the corrosion rates remain relatively high, which has implications for engineering. To explain these high corrosion rates, a mechanistic model was proposed, including two combined effects: a chemical and an electrochemical effect. The different methods to determine corrosion rates were found to yield comparable results.
The aim of this work was to revisit second‐harmonic generation (SHG) as a technique for the in situ analysis of oxide film formation on steel samples immersed in aqueous solutions and during electrochemical experiments. The measurements were compared to active reflectance spectroscopy (ARS), which is a more established in situ spectroscopy technique. Carbon steel electrodes were subjected to polarization in pH neutral and mild‐alkaline electrolytes to provoke the formation of passive films. In situ SHG measurements allowed monitoring of compositional changes in the formed film, as the SHG intensity increased in the domain of stability of Fe3O4 and decreased in the domain of stability of Fe2O3 during potentiodynamic polarization. ARS, on the other hand, is suitable to monitor film thickness. ARS absorption increased along with film growth when moving in the anodic direction during potentiodynamic polarization. During 30 min cathodic polarization at −0.9 VAg/AgCl sat. KCl in initially pH neutral the combination of SHG and ARS revealed the presence of an oxide film that was primarily composed of Fe3O4 and with a thickness up to 0.7 nm.
Exploring the potential for secondary utilization of wastewater is a prudent strategy to achieve “take-make-use-reuse” circular economy. Taking advantages of wood’s hierarchical structure and large surface area, in this project, we fabricate surface-encapsulated anion-selective and cation-selective wood membranes (comprising up to 98% eco-friendly materials) through a two-step process: dip-coating with either positively charged 2(dimethylamino)ethyl methacrylate or negatively charged acrylic acid, followed by energy-efficient sunlight-induced polymerization. The output voltage and current of a single modified wood cell (20 × 20 × 3 mm 3 ) in modulated wastewater from flue gas desulfurization are 55 mV and 0.6 µA, respectively, tenfold higher than that of untreated wood cells. When five cells are connected in series, the output voltage reaches 0.27 V, sufficient to power simple electronic devices. This underscores its potential for scaling up and its viability for future applications in industrial power plants.