1 September 2003 in Microelectronic Engineering
12 February 2024 in Applied Physics Letters
In this study, we investigate the spin Hall effect in heterostructures of Bi0.85Sb0.15 (10 nm) topological insulator/Ru(Ti)/Ta/Co20Fe60B20/MgO with perpendicular magnetic anisotropy. By optimizing the Ru (Ti) interfacial layer thickness as well as deposition condition of BiSb, we achieve a large effective spin Hall angle of 6.0 ± 0.1 and relatively high electrical conductivity of 1.5 × 105 Ω−1 m−1 at room temperature. We, then, demonstrate spin–orbit torque-induced magnetization switching driven by a small threshold current density of 1 × 106 Acm−2. Benchmarking shows that the writing power consumption of our stack is 2–3 orders smaller than that of heavy metals.
30 January 2023 in Applied Physics Letters
It is technically challenging to shrink the size of a tunneling magnetoresistance reader to below 20 nm for magnetic recording technology beyond 4 Tb/in2 due to its complex film stack. Recently, we proposed a reader architecture based on the inverse spin Hall effect to resolve those challenges, referred below as spin–orbit torque (SOT) reader, whose structure consists of a SOT layer and a ferromagnetic layer. However, the heavy metal-based SOT reader has small output voltage and low signal-to-noise ratio (SNR) due to the limited spin Hall angle θSH (< 1) of heavy metals. In this Letter, we demonstrate the integration of BiSb topological insulator with strong inverse spin Hall effect into the SOT reader that can significantly improve the output voltage and SNR. First, we theoretically calculate the noises in a 20 × 20 nm2 BiSb-based SOT reader to establish the relationships between SNR and θSH at various bias currents. We then demonstrate proof-of-concept BiSb-based SOT readers using CoFe/MgO/BiSb stack, which show large output voltages up to 15 mV at an input current of 9.4 kA/cm2 at room temperature. We project a giant θSH = 61 for BiSb. Our work demonstrates the potential of BiSb for SOT reader beyond 4 Tb/in2 magnetic recording technology.
17 November 2022 in Journal of Vacuum Science & Technology A
Trends in device miniaturization have driven the adoption of new materials that, in turn, have enabled significant advancements in the field of process engineering and integration for semiconductor technology. Continued progress for device scaling is necessary and can be enabled by advances in lithographic techniques and deposition schemes. Thin-film deposition for spacers and etch stop layers has become a mainstay to enable and extend traditional 2D scaling into the 3D realm for fabricating advanced semiconductor devices. For processing 3D structures, controlled film deposition with subnanometer resolution in high aspect ratio features is desired. Area selective deposition (ASD) can be a powerful response to such a challenge. ASD is a type of thin-film deposition technique scheme that can be used to eliminate the need for several expensive and time-consuming lithography steps with fewer performance penalties. In this work, we show ASD of ruthenium (Ru) on 3D molybdenum (Mo)–silicon oxide (SiO2) stacks by utilizing the inherent substrate preference of the Ru precursor to a H-terminated surface. In the best selectivity condition, our results show growth of ∼5 nm Ru on Mo, with no film growth on SiO2. Changes in Ru growth kinetics were observed after dilute hydrofluoric acid (DHF) treatment for both surfaces. Post-DHF treatment, the Ru growth rate on Mo was reduced by 5%. However, on SiO2 (after incubation delay), the growth rate was reduced by 94% compared to untreated surfaces. This translates to a very high difference in the growth rate of Ru on Mo vs SiO2, even after considering the incubation delay. Finally, by using 3D topologies with high aspect ratio holes, we have highlighted that it is important to deconvolute the effects of precursor depletion and selectivity. To the best of our knowledge, this is the first demonstration of ASD of Ru on 3D structures without the use of any blocking layers. Therefore, these results demonstrate a new paradigm for ASD in 3D features.
25 August 2023 in Journal of Vacuum Science & Technology A
Recent trends in semiconductor process engineering have resulted in significant adoption of new materials and processes to enable new paradigms in device manufacturing. One such emerging process is area selective deposition where a material can be selectively deposited on an area of interest. In this work, we have demonstrated selective deposition of ruthenium (Ru) on amorphous (a-Si) and polycrystallized silicon (p-Si) to silicon dioxide (SiO2) on both 2D blanket films as well as 3D annealed SiO2–Si multilayer stacks. Amorphous Si once crystallized using high temperature annealing exhibits reduced surface hydrogen content (–Si–H), yet we observed Ru growth on p-Si films that were annealed under multiple conditions (800, 900, and 1000 °C). We have used a combination of Fourier transform-infrared spectroscopy and x-ray photoelectron spectroscopy (XPS) to show that both –Si–H and film crystallinity impact the selective growth of Ru. We have also demonstrated selective deposition of ∼10 nm Ru on p-Si layers and ∼0 nm Ru on SiO2 layers of the annealed 3D SiO2–Si multilayer stack. Additionally, by using a combination of XPS and transmission electron microscopy, we have demonstrated that Ru growth is higher on nongrowth surfaces in 2D substrates than on 3D stacks. Finally, we have shown that this process technology can be further advanced using a combination of selective and nonselective conformal atomic layer deposition processes to develop a novel 3D annealed SiO2–Si multilayer stack, thereby demonstrating a 3D device with low –H content p-Si films. This study can help us to realize new integration schemes for innovative 3D device structures.