1 September 2016 in Journal of Asian Ceramic Societies
Clay–alumina compositions of 0, 20, 40 and 55weight percent (wt%) clay and rest alumina were maintained in porous support preparation by extrusion followed by sintering at 1300°C for 2.5h to obtain 3mm/2mm (outer diameter/inner diameter) capillary. 1H,1H,2H,2H-perfluorodecyltriethoxysilane (97%) (C8) was used to modify the capillary surface of all compositions without any intermediate membrane layer to impart hydrophobic characteristics and compared in terms of contact angle produced by the capillaries with water and liquid entry pressure (LEPw). FTIR analysis showed that the hydrophilic surface of the capillary membranes was efficiently modified by the proposed grafting method. Capillary with 55wt% clay produced a pore size of 1.43micron and was considered as an ideal candidate for grafting with C8 polymer to impart surface hydrophobicity. The contact angle and LEPw value obtained for this modified membrane (C-55-M) were 145° and 1bar, respectively. The modified capillary membrane was applied for desalination of brine by air gap membrane distillation (AGMD) at a feed pressure of 0.85bar. Maximum flux obtained for C-55-M membrane was 98.66L/m2day at a temperature difference of 60°C with salt rejection of 99.96%. Mass transfer coefficient of C-55-M was 16×10−3mm/s at feed temperature of 70°C
1 November 2015 in Ecotoxicology and Environmental Safety
21 June 2019 in Journal of Micromechanics and Microengineering
We report the fabrication and testing of a multilayer flexible screen-printed coil that can be used to generate low-frequency (<1 kHz) magnetic fields for applications such as electrodynamic wireless power transmission (EWPT). Compared to traditional coil-forming methods, screen printing enables rapid fabrication of thin, light weight, conformable, and flexible structures. The flexibility is demonstrated by repeated bending of a stack of up to three layers for a curvature (inverse bending radius) of 53.2 . We also demonstrate wireless power transmission of 1 mW of power at a distance of 4 cm between the flexible receiver and transmitter. The effect of the flexibility is observed through a 32% power increase when the receiver is bent concavely and a 20% output power decrease when the stack is bent convexly. It is also seen that the insertion of a 0.2 mm-thick soft-magnetic material sheet increased the magnetic field by 41% from its original value. Mechanical cycling was also performed for the stack. After 10 000 bending cycles, a 16.4% increase in the coil resistance was measured for a 0.33 Hz frequency and 78% increase for a 1 Hz cycling frequency, respectively. Screen printed 3D flexible transmitter coils can enable the incorporation of EWPT for wireless charging in applications such as healthcare and consumer-based electronics.
4 June 2015 in Journal of Porous Materials
9 November 2018 in Journal of Micromechanics and Microengineering
Polydimethylsiloxane (PDMS) is known to be more flexible and stretchable than other commonly used substrates for flexible electronics, including thermoplastic polyurethane (TPU) and polyethylene terephthalate (PET). However, commercially available inks for printing flexible electronics are not formulated for PDMS, resulting in very poor adhesion of printed electronic components on PDMS. To address this limitation, we have developed a surface-modification method that enables inks to adhere firmly onto PDMS. Using the ASTM protocols (tape-pull test and pencil-hardness test), we confirmed that the surface modification method significantly improved the adhesion and abrasion resistance of conductive components fabricated on PDMS. In addition, we investigated using an airbrush as a low-cost alternative for fabricating flexible electronics. We compared airbrushing with screen printing, the common fabrication method used for flexible electronics. We found that the change in resistance of resistors airbrushed on both surface-modified PDMS and TPU was slightly less after 30–100 cycles of stretching than the same resistors screen-printed on the same substrates, indicating that airbrushing is able to fabricate electronic components of similar quality, if not better, when compared with screen printing. To further illustrate the effect of the surface modification method and airbrushing, we fabricated a patch antenna by airbrushing inks on surface-modified PDMS and pristine PDMS. The measurement results of the antenna on surface-modified PDMS showed a close agreement with the simulation result, giving a resonant frequency at 2.4 GHz.
17 November 2022 in Journal of Vacuum Science & Technology A
Trends in device miniaturization have driven the adoption of new materials that, in turn, have enabled significant advancements in the field of process engineering and integration for semiconductor technology. Continued progress for device scaling is necessary and can be enabled by advances in lithographic techniques and deposition schemes. Thin-film deposition for spacers and etch stop layers has become a mainstay to enable and extend traditional 2D scaling into the 3D realm for fabricating advanced semiconductor devices. For processing 3D structures, controlled film deposition with subnanometer resolution in high aspect ratio features is desired. Area selective deposition (ASD) can be a powerful response to such a challenge. ASD is a type of thin-film deposition technique scheme that can be used to eliminate the need for several expensive and time-consuming lithography steps with fewer performance penalties. In this work, we show ASD of ruthenium (Ru) on 3D molybdenum (Mo)–silicon oxide (SiO2) stacks by utilizing the inherent substrate preference of the Ru precursor to a H-terminated surface. In the best selectivity condition, our results show growth of ∼5 nm Ru on Mo, with no film growth on SiO2. Changes in Ru growth kinetics were observed after dilute hydrofluoric acid (DHF) treatment for both surfaces. Post-DHF treatment, the Ru growth rate on Mo was reduced by 5%. However, on SiO2 (after incubation delay), the growth rate was reduced by 94% compared to untreated surfaces. This translates to a very high difference in the growth rate of Ru on Mo vs SiO2, even after considering the incubation delay. Finally, by using 3D topologies with high aspect ratio holes, we have highlighted that it is important to deconvolute the effects of precursor depletion and selectivity. To the best of our knowledge, this is the first demonstration of ASD of Ru on 3D structures without the use of any blocking layers. Therefore, these results demonstrate a new paradigm for ASD in 3D features.