The paper considers the possibility of lifetime extending of the rod control cluster assemblies in operation by determining their residual lifetime using an approach that takes into account the actual position of the rod control cluster assembly in the core. Excessive conservatism was introduced by assuming that the immersion of the 10th working group in the core during all fuel campaigns is 70 %, while the actual position is 85-90 %. Taking into account the actual position of the rod control cluster assemblies indicates much less irradiation of the lower, most loaded part of control rod cladding and much less burnup of the 10B compared to 70 % immersion of the rod control cluster assemblies, since they are in the area of lower neutron flux density. The results of a comprehensive analysis of available studies and test results to determine the phenomena that can potentially approach the achievement of the boundary state of the structural components or limit the lifetime of control rods and rod control cluster assemblies in general are presented. Such phenomena include general corrosion of structural materials (42CrNiMo, Cr18Ni10Ti) (decrease in wall thickness, increased transfer of radioactive corrosion products the coolant); radiation resistance (degradation of mechanical characteristics) of control rod cladding materials (42CrNiMo) and other structural components of the rod control cluster assemblies (42CrNiMo, CrKh18Ni10Ti); radiation resistance of neutron-absorbing materials (B4C, Dy2O3∙TiO2); compatibility of absorbing materials with the control rod cladding. Based on the results of post-irradiation examinations of control rods tested in research reactors as dummy rods or rod control cluster assembly rods operated in the VVER-1000 core, the following boundary values were established that can be used as criteria for maintaining the integrity of the control rod cladding: maximum fast neutron fluence in the lower, most loaded part of the control rod cladding (in the weld area of the lower end plug and the cladding) should not exceed 34×1021 n/cm2; maximum burnup of the 10B isotope should not exceed 45 %. If these two criteria are met, the possibility of other potentially damaging phenomena is too low. According to the calculations that use the schedule of changes in the position of the rod control cluster assemblies of the control group and the power of one of the power units during one fuel cycle, one can preliminary conclude that the proposed approach will extend the lifetime of almost all rod control cluster assemblies from 25500 to 38000 hours in the automatic control group and from 75600 to 113500 hours in the shutdown group. The residual lifetime should be assessed for a particular power unit and each rod control cluster assembly separately, since each rod control cluster assembly has its own operating history.
The uninterrupted operation of Ukrainian NPPs depends not only on timely delivery of fresh fuel, but also on the supply of a number of other critical core elements. One of these critical elements is control rods, which have their own lifetime and need to be replaced on a regular basis. If the diversification of nuclear fuel suppliers has been ongoing since the early 2000s [1], the diversification of control rods was at the initial stage at the beginning of the full-scale invasion and its completion requires some time to conduct the relevant tests and trial operation in the reactor core. For temporary meeting the NPP need for control rods, it was decided to justify lifetime extension for them by determining the residual lifetime. Control rod lifetime extension is based on the determination of the residual lifetime using an approach that takes into account control rod actual position during all fuel campaigns in which the control rods were operated. Excessive conservatism was laid due to the assumption that the immersion of the 10th working group in the core during all fuel campaigns is 70 %, but the actual position is 85–90 %. To reduce conservatism, it is necessary to take into account the actual position of the emergency control groups during all fuel campaigns in which the control rods were part of the control group that requires a large number of neutronic calculations to determine the neutron fluence and absorbing element burnup (boron-10). The obvious approach to determining the fluence of fast neutrons and boron burnup in absorbing elements is currently the use of the Monte Carlo method, which allows modeling neutron transport without any serious assumptions and approximations of the computational model, and, accordingly, present the most accurate results. The main disadvantage of Monte Carlo codes is that the simulation of complex systems is a long-term computational process, which can become a limiting factor. Considering the need to take into account the actual operation schedule of each control rod, the application of the Monte Carlo method to justify the operability in the lifetime extension for control rods is extremely problematic. The approach to neutronic calculations using the HELIOS code is proposed in the paper in terms of determining the fluence of fast neutrons and burnup of the boron-10 isotope in absorbing elements. The approach is based on the application of the neutron transport solution in two-dimensional geometry based on the method of the first collision probability and the subsequent synthesis of two- and one-dimensional neutron flux density distributions. The implemented approach is characterized by an accuracy comparable to the Monte Carlo method but is much more efficient in terms of computer time spent for calculations, which allows a large amount of calculations to be performed to justify the lifetime extension for each individual control rod, taking into account the real history of operation.
5 November 2021 in Automation of technological and business processes
У статті розглянуто перспективну можливість вирішення актуального для об’єднаної енергосистеми України питання щодо досягнення в останній високих показників стабільності її частоти. Відомо, що досягнути високих показників стабільності частоти намагались і за існуючих традиційних методів їх формування однак, навіть на протязі декількох останніх десятиліть зробити це так і не вдалося. За результатами проведених в роботі досліджень визначено, що досягнути високих показників стабільності частоти в об’єднаній енергосистеми буде цілком можливо навіть в умовах її самостійної роботи, якщо у місцевих енерговузлах, що живляться безпосередньо від станції АЕС, забезпечити відповідні умови для формування резервів маневрених потужностей, які будуть використовувати у процесах первинного, вторинного і третинного регулювання частоти. В роботі науково обгрунтовано і перспективну можливість створення на станціях АЕС принципово нової системи протидії процесам збурення режиму. Нова система в разі появи в об’єднаній енергосистемі процесу збурення її режиму здатна буде вчасно і адекватно виконувати протидію цьому процесу, що забезпечить можливість збереження попередньо встановленого в енергосистемі режиму із попередньо встановленим значенням частоти. Можна передбачити, що за створення нових систем керування процесами первинного, вторинного і третинного регулювання частоти безпосередньо у електромережі АЕС стане цілком можливим досягнути в об’єднаної енергосистеми України нових високих показників стабільності частоти, що відповідатимуть рівню її стабільності в енергооб’єднанні ENTSO-E. Висока енергетична ефективність визначеного перспективного напрямку щодо використання електротеплових генераторів в процесах управління режимом енергосистеми була підтверджена результатами проведених досліджень, тому саме цей напрямок повинен стати одним із пріоритетних у планах подальшого розвитку ОЕС України.
The paper considers one of the possible options to solve the actual task for the Integrated Power System (IPS) of Ukraine regarding creating deficit-free primary, secondary and tertiary reserves, which is an important condition for successful integration of IPS of Ukraine into ENTSO-E. The increase of the level of reserves of IPS of Ukraine could be provided by the implementation of the dedicated technological system (NPP+powerful electric boilers) which should be connected at the "points" where a nuclear power plant (NPP) is connected to the grid. It is assumed that the use of the proposed technological system with electric boilers' capacity of 2000 MW in the IPS of Ukraine will allow the substitution of about 10 thermal power plant's (TPP) units, which provide secondary reserves. Implementation of proposed option also aimed at fulfillment "National Plan on Reduction of Emissions from big burning units", and also allow reduce consumption of organic fuel, namely the coal, that is prescribed by Energy Strategy of Ukraine till 2035. According to preliminary estimates, the proposed technological system complies with the main categories of "Methodology for the analysis of costs and benefits of projects for the development of electrical networks". Keywords: integrated power system, electric boiler, load profile, wholesale electricity market
The article considers promising directions for the construction of new systems for regulating the generating capacity of nuclear, solar and wind power plants, capable of changing and improving the processes of managing the load regime of the unified energy system of Ukraine. Conducted studies have shown that with the implementation of new systems, there is a real opportunity to abandon modern but too expensive means of maneuverable generation, such as reserve stations with highly maneuverable TPPs, as well as frequency control support systems (FCS) using powerful storage batteries. In contrast to this, it is offered in the processes of managing the regime of the unified energy system of Ukraine, applying the new principles and means of regulating the generating capacities of NPPs, as well as WPPs and SPPs. For this, it will be necessary to create reserves from the automatically controlled load of powerful EC electric boilers in the OESU. At the same time, only the automated dispatching control system (ADСS) will perform the load regulation processes of powerful ECs. It is assumed that the information data on the current load regulation parameters of the ECs complexes will be sent to the ADСS from specialized tools built on the basis of the use of information and measurement technologies (IMT) developed at the Institute of General Energy on NAS of Ukraine. The result of the conducted research is the development of methodical approaches to the management of the OES regime, using new principles of regulation of generating capacities both in the power grid of NPPs and in the cities where WPPs and SES are installed. Keywords: power system, electric heat generators, load schedule, control system
Considered a promising possibility in the system of dispatching control of the load mode of the United energy system of Ukraine to ensure the processes of regulating the generating capacities of NPP stations. The new direction of construction of control systems using the United energy system of Ukraine mode will make it possible to abandon too expensive means of maneuverable generation, such as the construction of reserve stations with highly maneuverable TPPs that have high-speed start-up characteristics, as well as frequency control support systems using powerful storage batteries. Instead, it is proposed to use powerful automatically controlled electric boilers, previously included in the means of regulating the load regime of the combined energy system. This will contribute to the further development of the generating capacity of nuclear power plants, wind power plants, and thermal power plants, as well as to the resolution of issues related to ensuring the stability and sustainability of the combined power system.