20 June 2025 in IEEE Transactions on Transportation Electrification
Coaxial magnetic gear (CMG) exhibits the advantages including lubrication-free, inherent overload protection, and less maintenance cost; thus, it has received lots of attention in low-speed high-torque applications. However, the majority of CMG research is concentrated on the development of innovative topologies, and the investigation of the flux density harmonic characteristics is barely seen. In this article, a new perspective of analyzing the flux density harmonic characteristics is presented for three most typical CMGs, i.e., surface-mounted CMG (SM-CMG), spoke-type CMG (ST-CMG), and triple-layer CMG (TL-CMG). On this basis, the corresponding contributions of the flux density harmonics to the average torque are comparatively studied and quantified. In addition, the three CMGs are globally optimized based on the multiobjective genetic algorithm (MOGA), to allow for a more comprehensive comparison of other key performances. The results indicate that the TL-CMG has the best overall performance among these CMGs. As the CMG is usually integrated with the motor, the integration pattern of the two is analyzed. Finally, a prototype for the automated guided vehicle (AGV) robot application is built and tested, and the experimental results match well with the simulation results.
16 April 2025 in IEEE Transactions on Energy Conversion
Accurate electrical and mechanical parameters are crucial for designing high-performance controllers in induction motor (IM) sensorless control systems. In this paper, a self-commissioning scheme, which involves the identification of electrical and mechanical parameters, is presented for IM sensorless drives. First, the inverse-Γ equivalent circuit parameters required for the current controller autotuning are identified using the proposed single-phase voltage injection method, which only utilizes the time-domain response to identify electrical parameters while accounting for the influence of the inverter nonlinearity. Then, a mechanical parameter identification scheme independent of the speed controller is proposed for sensorless control systems. A sliding mode observer is designed to identify both the moment of inertia and load torque simultaneously. In addition, the identified electrical and mechanical parameters enable both offline and online tuning of controller parameters. Finally, the validity and effectiveness of the proposed methods are verified by experimental tests.
1 March 2016 in Journal of Renewable and Sustainable Energy
A thermal growth model for microalgae that are not heavier than water with the consideration of heat transfer and growth-temperature dependence in photobioreactor (PBR) is developed. The microalgae growth performance is studied, and influences of various parameters on the performance are examined. Improved methods are proposed to increase the biomass concentration in the PBR. Results show large increase in biomass productivity due to the addition of a mixer in the PBR, and slightly larger increase in productivity when cultivating microalgae at several middle layers with a mixer and filter membranes. Some layers in the PBR may effectively act as insulation layers in this case. This work lays a solid foundation for further study on the effect of the mixing on the growth and productivity of microalgae in the PBR.
20 May 2025 in IEEE Transactions on Industry Applications
Spoke-type (ST) magnetic geared permanent-magnet machine (MGPM) has been reported to exhibit higher torque density than regular surface-mounted (SM) MGPMs. However, this assertion is mainly based on finite element analysis (FEA), and the in-depth mechanism is not clear. This paper provides a new perspective on the torque generation mechanism of the ST-MGPM using the harmonic characteristic analysis. First, the working principles of the ST-MGPM and SM-MGPM are presented, showing that their torque densities are limited by the corresponding coaxial magnetic gear (CMG) part. Then, the radial and tangential harmonic characteristics in the ST-CMG and SM-CMG are analytically derived, identifying the predominant harmonics that contribute to the transmission torque. On this foundation, a harmonic-oriented multi-level optimization method of the ST-MGPM is proposed, which has higher optimization efficiency because only the magnetostatic FEA is needed. Finally, a prototype of the ST-MGPM is built and tested to verify the theoretical analyses.
16 September 2025 in IEEE Journal of Emerging and Selected Topics in Power Electronics
The voltage model-based flux observer is widely used in induction motor sensorless drive systems. Conventional rotor flux observer suffers from DC offset and high-order harmonics, which degrade the estimation performance of rotor speed and position. To address the above issue, an improved complex-coefficient flux observer is proposed in this article, along with a detailed dynamic performance analysis of the proposed observer. Compared with the conventional complex-coefficient observer, the proposed observer can effectively suppress high-order harmonics. To further eliminate DC offset, an offset estimator with frequency adaptive gain is proposed. Owing to the designed adaptive gain obtained from the small signal model of the offset observer, the offset estimation error can converge rapidly at different operating frequencies. The effectiveness of the proposed flux observer and offset observer is verified through a series of experiments on a 1.5-kW induction motor sensorless drive platform.