15 April 2019 in IEEE Transactions on Industrial Electronics
The reverse LLC voltage gain is lower than unity. The DC-link voltage is then lower than the peak grid voltage so that the buck type DC-AC converters cannot be grid-tied directly, which causes the LLC reverse operation difficult in bidirectional application. This paper proposes a SiC bidirectional LLC charger architecture to achieve high efficiency and high power density. The first stage is an interleaved bridgeless totem pole PFC to achieve unity power factor. The second stage is a 300-kHz LLC taking advantage of wide ZVS range and magnetic integration. Thanks to extra control freedom of high DC-link voltage, the DC-DC voltage gain regulation is shared by the DC/AC stage taking advantage of high voltage SiC MOSFETs. A reverse LLC voltage gain compensation control by regulating DC-link voltage is proposed to enable the LLC bidirectional operation. A digital adaptive synchronous rectification driving scheme is proposed based on the LLC primary driver signals, which immunes to the circuit oscillation caused by high dv/dt and parasitic elements. A 6.6 kW SiC bidirectional LLC charger was built. The power density is 3.42 kW/L with 3 kW /kg and increases 55.6% over the reference design. The charging efficiency is above 96% through the battery voltage from 240 V to 420 V, and 2% higher than the state-of-the-art products. The peak discharging efficiency under 6.6 kW is 96%, and 1% higher than the state-of-the-art efficiency.
19 January 2021 in IEEE Journal of Emerging and Selected Topics in Power Electronics
A SiC bidirectional portable charger is proposed to realize both bidirectional ac–dc and bidirectional dc–dc high-efficiency power conversion by multiplexing the same powertrain. Control strategies for different operation modes are proposed to realize the comprehensive functions of the portable charger. The proposed portable charger enables the EV to interact with the ac grid, dc microgrid, other EVs, and off-line loads efficiently and conveniently. The SiC portable charger adopts 300-kHz high-frequency isolation to improve the power density. The proposed vehicle-to-vehicle (V2V) mode adopts two-stage direct dc–dc power conversion so that it achieves higher efficiency compared with conventional V2V mode using an on-board charger (OBC). A 6.6-kW SiC bidirectional portable charger is built and the power density is 14.7 W/in 3 . The full-load efficiency of V2V mode is 96.1%, which is 4.7% improved compared with the conventional V2V mode. Bidirectional energy interaction between EV and the 380-V dc microgrid is also verified. The portable charger provides 36–400-V wide output voltage for dc loads with the efficiency above 95.7% at 6.6 kW.
12 October 2022 in IEEE Transactions on Industrial Electronics
Conventional CLLC synchronous rectification (SR) typically adopts detection circuits to sense the high frequency signals. It can hardly be used in the high-voltage SiC applications directly as it is sensitive to high dv/dt and may cause false operation. A bidirectional control is proposed for the SiC CLLC charger to achieve the SR function and mitigate the input ripple current. Considering the switching frequency and load, the SR on-time is calculated by the proposed three-order fitting model with low calculation source and high immunity to high dv/dt . Moreover, an input ripple current feedforward control is proposed in the discharging mode, which adds the extracted double line-frequency ripple current to the bus voltage reference. It not only achieves low SR conduction loss, but also reduces the input ripple current largely in the discharge. A 6.6-kW SiC bidirectional CLLC charger was built. Compared to the conventional SR, the CLLC efficiency of proposed SR improves 0.28% at 6.6 kW in the charge. In the discharge, the reduction of CLLC input ripple current at the double line-frequency is up to 91%. The overall charging and discharging efficiencies are 95.4% and 96.1% at full load, respectively.
29 September 2020 in IEEE Transactions on Power Electronics
With 700 V bus voltage in the SiC bidirectional LLC converters, high dv/dt is up to 35 kV/μs with 20 ns switching speed, which causes high common mode noise and poses serious challenge for synchronous rectification (SRs) control. A digital bidirectional SR online calculation control is proposed for 700 V high voltage at 300 kHz. It not only achieves bidirectional operation with high efficiency, but also applies to high voltage since it owns high immunity to the switching noise without any detection circuits. The mathematical model is built to calculate the SR conduction time online in the forward and reverse modes, and determine the SR turn off instant considering the switching frequency and load. The transformer dc bias is analyzed in the reverse mode. A 6.6-kW SiC bidirectional portable charger was built. The LLC efficiency of forward and reverse modes is improved by 0.3% and 0.2% over the conventional SR control at full load, respectively.
10 November 2021 in IEEE Transactions on Power Electronics
Conventional pulse frequency modulation is typically adopted in the reverse LLC converter resulting in a low voltage gain. The output bus voltage may be lower than peak grid voltage, so that the buck-type inverter cannot output 220 Vac and poses series challenge to achieve bidirectional charger operation. A bidirectional synchronous/asynchronous rectifier control is proposed for wide battery voltage applications in the LLC converter. In the forward mode, a simplified model is built to calculate the synchronous rectifier (SR) on-time and achieve high efficiency by using a two-order function. In the reverse mode, the turn-on instants of primary side and secondary side power devices are controlled with a delay angle to obtain high voltage gain and high efficiency. A 6.6-kW silicon carbide bidirectional LLC charger was built. With the proposed SR control, the forward LLC efficiency improves 0.2% compared with the conventional SR method. The reverse LLC voltage gain is up to 1.33 so that the charger can output 220 Vac in the full battery voltage range of 200–500 V.
3 December 2020 in IEEE Transactions on Power Electronics
For 1-MHz GaN LLC converters with 1-kV input, the switching speed of eGaN HEMTs is as fast as 6 ns, which results in dv/dt up to 200 kV/s. It poses serious challenge for Synchronous Rectification (SR). A sensorless model-based SR driving scheme is proposed to optimize the efficiency at steady state and the complementary control as an interlock mechanism is applied during the transients to ensure safety. A mathematic model is built to determine the turn-on instant and conduction time related to the switching frequency and load condition so that the driving signals are adjusted adaptively. The proposed method provides reliable gate driving signals without detection circuits and is immune to high frequency noise. The transient response is analyzed and the tolerance effects of the resonant components are analyzed quantitatively. This control is fully transparent to design engineers compared to SR drive ICs, and is convenient to implement in high voltage and high frequency applications. A 1-MHz prototype with 1 kV input and 32 V/ 3 kW output is built, which achieves the power density of 103 W/in3 and peak efficiency of 95.92% with an improvement of 2.0% at full load compared to the conventional SR driving scheme.