20 July 2022 in IEEE/ASME Transactions on Mechatronics
In magnetic suspended centrifugal compressors, the unbalanced magnetic pull (UMP) may cause saturation on power amplifier currents driving the coils of the active magnetic bearing (AMB), eventually affecting the stability of the rotor. This article addresses the issue on the stable operation of the AMB-rotor system subject to the UMP. A mathematical model of the UMP with uneven magnetization of permanent magnet (PM) and eccentricity is proposed for a surface-mounted PM synchronous motor supported by magnetic bearings. Based on this model, an improved radial magnetic bearing (RMB) with control and bias separated coil structure is designed and optimized to decrease the compensation current used to balance the UMP. First, a mathematical model containing the unevenness of the magnetization and eccentricity is established to estimate the UMP. Next, the compensation current for the UMP is analyzed based on the UMP model. Then, with the aim of minimizing the compensation current, the proposed RMB is optimized under the constraints of the starting current, the magnetic bearing volume, and the coil current density. The compensation current of the optimized RMB is reduced by 25%, compared with that of the original RMB. Finally, the experimental results on a 132-kW magnetic suspended centrifugal compressor, equipped with the optimized RMB, show the effectiveness of the modeling and optimization design.
5 February 2024 in IEEE Transactions on Energy Conversion
In the high-speed magnetically suspended air compressor, there is a significant pressure difference on both sides of the rotating impeller, which subjects the rotor to considerable axial force. In this case, the axial load capacity provided by the magnetic bearing is required to be very high, even much greater than the radial load capacity. To meet this requirement, a novel three-degree-of-freedom magnetic bearing is proposed in this paper. Compared to the conventional magnetic bearing, this structure offers a higher ratio of axial to radial load carrying capacity. In order to analyze the performance characteristics of the novel magnetic bearing, a new integrated magnetic circuit model based on detailed calculations of complex leakage flux paths is created. The main problems of force non-linearity and cross-coupling effects between different directions are investigated through the magnetic circuit model. The prototype has been designed and fabricated, and the results of both experiments and simulations show that the proposed structure and model are feasible and valid.
16 November 2023 in IEEE/ASME Transactions on Mechatronics
An axial hybrid magnetic bearing (AHMB) with the slice stator for the magnetic suspension centrifugal compressor (MSCC) is presented in this article. With the advantages of short axial length, high axial bearing capacity, small thrust disk, and easy installation, this structure is suitable for the requirements of high-speed MSCCs. First, the accurate stator region segmentation method is used to establish the equivalent magnetic circuit model, which overcomes the error caused by the complex magnetic leakage path and the nonlinear stator material of the existing model due to the slice stator. Then, it is found that the internal layout of the stator affects the magnetic circuit distribution of the stator combined with the improved magnetic circuit model, which has a significant impact on the performance of the magnetic bearing. The optimum internal structure of the AHMB with the slice stator is proposed. Finally, the proposed AHMB is manufactured and assembled into the prototype of the MSCC, where the force–current experiment and the speed-up experiment are performed. Simulation and experimental results validate that the proposed AHMB and the improved magnetic circuit model can effectively work for the MSCC.
4 July 2024 in IEEE Transactions on Industrial Electronics
The characteristic of high-speed magnetic levitation motors is that the rotor is relatively short to meet the requirements of rotor dynamics. Therefore, the internal layout of electromagnetic components in the system is more compact, and the distance between the magnetic bearing (MB) and the motor is closer. The magnetic field of the MB leaks into the motor through narrow air gaps, forming interference magnetic fields. This article focuses on analyzing the magnetic field crosstalk phenomenon in the high-speed magnetic levitation motor caused by the strict restrictions on the axial length of the rotor. An integrated magnetic equivalent circuit (MEC) model contains the MB and motor is proposed to calculate the magnetic flux density of the air gap and the degree of crosstalk. Based on the calculation results of the integrated MEC model and the axial length limit under rotor dynamics, a reasonable layout and position distribution are determined to reduce the degree of crosstalk. Through experiments, it is found that the maximum error in calculating the current stiffness of the MBs using the model proposed in the article is 9.43%, with relatively high consistency. Additionally, the amplitude of the MB suspension current decreases from 0.20A to 0.02A after layout optimization.
12 June 2026 in IEEE/ASME Transactions on Mechatronics
Hybrid magnetic bearings (HMBs) play a critical role in allowing magnetically suspended turbomolecular pumps to attain ultra-high vacuum conditions. However, current modeling and optimization approaches for HMB design do not account for the magnetic field coupling between the HMBs and the motor. This omission leads to deviations in the model, inaccurate optimization directions, and difficulties in designing magnetic suspension systems that simultaneously achieve high load capacity and a more compact integrated structure. To address this issue, this article presents a comprehensive HMB design method integrating modeling, sensitivity analysis, and optimization. First, the integrated equivalent magnetic network model is established to analyze the electromagnetic characteristics of the HMBs, which accounts for magnetic coupling effects. Then, a pointwise sensitivity analysis is proposed to quantify the influence of design variables on multiple objectives across the feasible domain and is incorporated into a multiobjective particle swarm optimization algorithm to efficiently guide the search direction. Compared with the preoptimization design, the proposed method improves the weighted average of the maximum radial forces of the two HMBs by 57.03%, reduces the axial length by 11.52%, and mitigates the magnetic coupling by 71.85%. Finally, both simulation and experimental results confirm the effectiveness of the proposed method.
9 June 2025 in IEEE Transactions on Power Electronics
Conventional loss minimization control (LMC) strategies can reduce electrical losses of high-speed surface-mounted permanent magnet synchronous motors (SPMSMs) by regulating the d-axis current to its optimal value. However, their performance is limited by the accuracy of the optimal current calculated based on fixed model parameters. Considering that some model parameters are prone to change during the operation of high-speed SPMSMs, this article proposes an improved LMC strategy based on online parameter estimation. First, the impact of model parameter variations on electrical losses and optimal current is analyzed. Second, lookup tables for stator resistance and synchronous inductance, along with a super-twisting sliding mode observer, are designed for the estimation of dq-axis magnetizing currents, which are used to estimate the iron loss resistance. Subsequently, addressing the issue of increased system complexity due to the introduction of electromagnetic torque in traditional LMC strategies, this article directly adopts the optimal magnetizing current as the reference and designs an improved LMC strategy using the observed magnetizing current as feedback. Finally, the effectiveness of the proposed method is validated through experiments on a high-speed magnetic levitation air spinning machine, demonstrating significant reduction in electrical losses and improved efficiency.