19 May 2020 in IEEE Access
For the first time, the design and implementation of a fully-integrated wireless information and power transfer system, operating at 24 GHz and enabling battery-less sensor nodes, is presented in this paper. The system consists of an RF power source, a receiver antenna array, a rectifier, and a battery-less sensor node which communicates via backscatter modulation at 868 MHz. The rectifier circuits use commercially available Schottky diodes to convert the RF power to DC with a measured efficiency of up to 35%, an improvement of ten percentage points compared with previously reported results. The rectifiers and the receive antenna arrays were jointly designed and optimised, thereby reducing the overall circuit size. The battery-less sensor transmitted data to a base station realised as a GNU Radio flow running on a bladeRF Software Defined Radio module. The whole system was tested in free-space in laboratory conditions and was capable of providing sufficient energy to the sensor node in order to enable operation and wireless communication at a distance of 0.15 metres.
18 June 2018 in Journal of Physics D: Applied Physics
This paper presents, for the first time, a multimodal sensor for characterizing relative permittivity of plastic polymers by integrating in a single sensor (1) frequency-reconfigurable resonance technique at 98 and 100 GHz, and (2) 80–100 GHz broadband modified transmission-line technique. The sensor is designed based on a custom-made WR-10 waveguide featuring dual rectangular complementary split-ring resonators (CSRRs). By loading the CSRRs with a material-under-test (MUT), the reflected and transmitted electromagnetic waves propagating inside the waveguide are changed depending on the dielectric properties of the material. Various plastic polymer materials, e.g. polytetrafluoroethylene (PTFE), polymethylmethacrylate (PMMA) and high-density polyethylene (HDPE), are characterized. The sensor in this paper offers various key advantages over any state-of-the-art material characterization techniques at millimeter-wave frequencies, e.g. multiple characterization techniques integrated in a single device, miniaturization, much higher tolerance to changes in the measurement environment, ease of design and fabrication, and better cost effectiveness.
5 June 2018 in IEEE Transactions on Components, Packaging and Manufacturing Technology
This paper presents a low-cost microfabrication technique for manufacturing radio frequency microelectromechanical system (RF MEMS) switches and varactors without intensive clean-room environments. The fabrication process entails only laser microstructuring technique, non-clean-room microlithography, and standard wet-bench and hot-film emboss of SU-8 and ADEX polymers. MEMS movable structures were fabricated out of 14-μm-thick aluminum foils and suspended above coplanar-waveguide transmission lines, which were implemented on top of FR4 substrates via 5-μm-thick SU-8 dielectric anchors. Both MEMS structures and an FR4 substrate were integrated using micropatterned polymers, developed by using dry-film ADEX and SU-8 polymers, for a composite assembly. An average fabrication yield of higher than 60% was achieved, calculated from 10 fabrication attempts. The RF measurement results show that the RF MEMS devices fabricated by using the novel microfabrication process have good figures of merit, at much lower overall fabrication costs, as compared to the devices fabricated by conventional clean-room process, enabling it as a very good microfabrication process for cost-effective rapid prototyping of MEMS.
30 December 2024 in IEEE Access
This study presents the development of an advanced machine learning model based on a two-dimensional (2D) Radio Frequency (RF) sensing framework for refined monitoring of femoral bone fractures. Utilising MATLAB simulations, we created a comprehensive dataset enhanced with variations in bone diameter, muscle thickness, fat thickness, and hematoma size, augmented with multiple sensor configurations (two, four, six, and eight sensors). The model aims to provide a frequent, non-invasive assessment of the fracture healing process compared to conventional imaging methods. Our approach leverages data from six RF sensors, achieving a high overall accuracy of 99.2% in classifying different fracture stages, including "no fracture" and varying degrees of hematoma sizes. The findings indicate that increasing the number of sensors up to six significantly enhances detection accuracy and sensitivity across all fracture stages. However, the marginal improvement from six to eight sensors was not statistically significant, suggesting that a six-sensor configuration offers an optimal balance between performance and system complexity. The results demonstrate significant potential for this technology to revolutionise orthopaedic treatment and recovery management by offering continuous, real-time monitoring without radiation exposure. The proposed system enhances personalised patient care by integrating RF sensing with artificial intelligence, enabling timely interventions and more informed, data-driven treatment strategies. This research lays a robust foundation for future advancements, including three-dimensional modelling and clinical validations, toward the practical implementation of non-invasive fracture monitoring systems.
1 August 2020 in Additive Manufacturing
MSMatthew P. Shuttleworth
+6