Nikhilendu Tiwary

Nikhilendu Tiwary

Auto-generated profile, based on publicly available information

Nikhilendu Tiwary

Department of Electrical Engineering and Automation, School of Electrical Engineering, Aalto University 1 , Espoo 02150

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 December 2022 in IEEE Transactions on Electron Devices
Verified
Journal Article
Open access
NTNikhilendu Tiwary
Nikhilendu Tiwary
GRGlenn Ross
Glenn Ross
VVVesa Vuorinen
Vesa Vuorinen
Mervi M. Paulasto-KröckelMervi M. Paulasto-Kröckel
Mervi M. Paulasto-Kröckel
Continuous scaling of package architectures requires small volume and high-density microbumps in 3D stacking, which often result in solders fully transforming to intermetallic compounds (IMCs). Cu–Sn solid–liquid interdiffusion (SLID) bonding is an attractive technology where the $\mu$ bumps are fully composed of IMCs. In this work, test structures made up of Cu $_{\text{3}}$ Sn IMC $\mu$ bump with a lateral dimension of 25 $\mu$ m $\times$ 25 $\mu$ m and 50 $\mu$ m $\times$ 50 $\mu$ m, respectively, were manufactured on a pair of 4-inch Si wafers demonstrating wafer-level bonding capability. Electromigration (EM) tests were performed for accelerated conditions at a temperature of 150 $^{\circ}$ C for various current densities ranging from $\approx $ 2 $\times$ 10 $^{\text{4}}$ to $\text{1}$ $\times$ 10 $^{\text{5}}$ A/cm $^{\text{2}}$ . Scanning electron microscopy (SEM) and elemental dispersive spectroscopy (EDS) were employed to characterize the as-fabricated test structures. Due to Sn squeeze out, Cu $_{\text{3}}$ Sn was formed at undesired location at the upper Cu trace. Both nondestructive lock-in thermography (LiT) and destructive techniques were employed to analyze the failure locations after EM tests. It was observed that the likelihood of failure spots is the current crowding zone along the interconnects in 3D architectures, which gets aggravated due to the formation of Cu $_{\text{3}}$ Sn in undesirable locations. Thermal runaway was observed even in Cu $_{\text{3}}$ Sn, which has been shown to be EM-resistant in the past, thus underlining inherent design issues of $\mu$ bumps utilizing SLID technology.

22 August 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Open access
SLShenyi Liu
Shenyi Liu
VVVesa Vuorinen
Vesa Vuorinen
XLXing Liu
Xing Liu
OFOlli Fredrikson
Olli Fredrikson
SBSebastian Brand
Sebastian Brand
Mervi M. Paulasto-KröckelMervi M. Paulasto-Kröckel
Mervi M. Paulasto-Kröckel
The die-attach layer is a vulnerable structure that is important to the reliability of an insulated-gate bipolar transistor (IGBT) module. A new failure mechanism named fatigue crack network (FCN) has been identified in the central area of the IGBT modules’ solder layer. In this article, to investigate the formation mechanism of the FCN, a fast power cycling test (PCT) (current on 0.2 s and current off 0.4 s) was designed and performed on a commercial IGBT module. Subsequently, scanning acoustic microscopy and X-ray imaging were used for nondestructive inspection of the defects of the solder layer. The cross section was based on the nondestructive inspection results. Then, electron backscattered diffraction analysis was carried out on both observed vertical and horizontal cracks. As a result, both networked vertical cracks at the center and horizontal cracks at the edge of the solder layer were detected. The recrystallization occurred during the PCT. The voids and cracks emerged at high-angle grain boundaries. A finite element simulation was performed to understand the driving force of FCN qualitatively. The stress simulation results indicate that under time-dependent multiaxial stress at the center of the solder, the defects nucleated, expanded, and connected vertically to form the FCNs.

1 September 2022 in Scripta Materialia
Verified
Journal Article
Open access
OGObert Golim
Obert Golim
VVVesa Vuorinen
Vesa Vuorinen
GRGlenn Ross
Glenn Ross
TWTobias Wernicke
Tobias Wernicke
MPMarta Pawlak
Marta Pawlak
Mervi M. Paulasto-KröckelMervi M. Paulasto-Kröckel
Mervi M. Paulasto-Kröckel

25 April 2022 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Open access
NTNikhilendu Tiwary
Nikhilendu Tiwary
VVVesa Vuorinen
Vesa Vuorinen
GRGlenn Ross
Glenn Ross
Mervi M. Paulasto-KröckelMervi M. Paulasto-Kröckel
Mervi M. Paulasto-Kröckel
Solid-liquid interdiffusion (SLID) bonding finds a wide variety of potential applications towards die-attach, hermetic encapsulation of MEMS devices and 3D heterogeneous integration. Unlike soft soldering technique, the solidification of intermetallic compound (IMC) formation in SLID bonding occurs during the process isothermally, making it difficult to predict and mitigate the sources of process-dependent thermomechanical stresses. Literature reports two dominant factors for the built-in stress in SLID bonds: volume shrinkage (due to IMC formation) and CTE mismatch. This work provides a detailed investigation of the Cu-Sn SLID bonding process by FE simulations. Specifically, the FE simulation of the SLID bonding process is divided into three steps: ramp-up, hold-time and ramp-down stages to understand the stresses formed due to each individual step. Plastic material properties for Cu as well as temperature dependent material parameters for different entities are assigned. Process-dependent thermomechanical stresses formed during the ramp-up and hold-time steps (IMC formation) were found not to be significant. The hold-time step is governed by the reaction and diffusion kinetics which determines the bond line quality including defects, such as voids. The ramp-down step is the dominant phase influencing the final stress formations in the bonds. The results show an average of >30% decrease in the stress levels in Cu3Sn layer (IMC) when the bonding temperature is brought down from 320 °C to 200 °C, thus demonstrating the importance of low temperature SLID process.

2 September 2016 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
NTNikhilendu Tiwary
Nikhilendu Tiwary
MVMadhuri Vinchurkar
Madhuri Vinchurkar
MPMihir Patel
Mihir Patel
RNRashi Nathawat
Rashi Nathawat
SPSwapnil Pandey
Swapnil Pandey
VRV. Ramgopal Rao
V. Ramgopal Rao
Preconcentrator integration with sensors for enhanced detection of target analytes, such as volatiles, explosives, and toxic compounds, has been gaining attention. Although metal oxides (MOX) have been widely used as gas sensors, they have not been employed for analyte preconcentration. In this paper, we have explored ZnO as a plausible trinitrotoluene (TNT) preconcentator material. A detailed study of these nanorods with respect to adsorption-desorption characteristics of TNT using specialized chromatographic techniques, such as gas chromatography-mass spectrometry (GC-MS) and high resolution liquid chromatography and mass spectrometry (HR-LCMS), was performed. A standard low temperature hydrothermal method was employed for the growth of ZnO nanorods. X-ray diffraction and scanning electron microscopy characterization confirmed the wurtzite crystal structure and uniform growth of these nanorods with diameter less than 100 nm and length between 4-5 μm. An HR-LCMS analysis confirmed adsorption of TNT on ZnO nanorods at ambient conditions as a result of its high trapping capability. Our GC-MS analysis confirmed that desorption of TNT from the surface of ZnO nanorods starts beyond 70 °C. A low power micro-hotplate with ZnO nanorods patterned and grown on top of it and having an in-built resistance temperature detector was fabricated. The fabricated micropreconcentrator was integrated with a highly sensitive polymeric piezoresistive microcantilever and a 2x (two times) improvement in its response was demonstrated.

9 August 2019 in Journal of Micromechanics and Microengineering
Verified
Journal Article
Closed access
PDF file
NTNikhilendu Tiwary
Nikhilendu Tiwary
MZMarjan Zakerin
Marjan Zakerin
FNFilipe Natalio
Filipe Natalio
EBEugen Biegler
Eugen Biegler
FMFritzsche Marco
Fritzsche Marco
VRV Ramgopal Rao
V Ramgopal Rao
Micro/nano thermogravimetry (TG) employing MEMS has significant potential to improve the minimum sample mass and mass resolution as compared to commercial TG instruments. Although there have been a few previous reports on MEMS TG, none of them have critically analysed the obtained TG curve in detail. In this work, we have designed and fabricated a microelectromechanical thermogravimetric device (MMTG) with integrated microheaters and temperature sensors. The mass sensitivity of the device was estimated to be 0.89 pg Hz −1 which outperforms the standard TG approaches. We tested the MMTG performance with CuSO 4 ·5H 2 O crystals. The final mass loss ratio corresponds to the theoretically expected value, although the obtained TG curve deviated from the standard TG curve of CuSO 4 ·5H 2 O obtained from commercial TG instruments. We attributed the deviation to the inherent temperature non-uniformity, non-isothermal conditions and temperature gradients of metallic-wire based microheaters. Finite element (FE) simulations were carried out in order to confirm and gain insights into the non-uniform heating phenomena of microheater and sample. Based on the simulation results, we propose designs that can be realized to make MEMS TG a successful enterprise.