Mervi M. Paulasto-Kröckel

Mervi M. Paulasto-Kröckel


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 March 2021 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Closed access
PDF file
EÖElmeri Österlund
Elmeri Österlund
HSHeli Seppänen
Heli Seppänen
KBKristina Bespalova
Kristina Bespalova
VMVille Miikkulainen
Ville Miikkulainen
Mervi M. Paulasto-KröckelMervi M. Paulasto-Kröckel
Mervi M. Paulasto-Kröckel
Atomic layer deposition (ALD) of aluminum nitride (AlN) using in situ atomic layer annealing (ALA) is studied for microelectromechanical systems (MEMS). Effective piezoelectric in-plane actuation and sensing requires deposition of high crystal quality and (0002) oriented AlN on vertical sidewalls of MEMS structures. Previous studies have shown that the crystal quality of ALD AlN can be significantly improved using ALA but have not studied the conformal coverage or crystal quality on metal electrodes, which are required for piezoelectric MEMS devices. In this study, AlN thin films are deposited on Si, Al, Pt, and on vertical sidewalls etched into Si. The AlN microstructure and properties are studied using x-ray diffraction methods, transmission electron microscopy, and Fourier transform infrared spectroscopy. The conformal coverage is evaluated by measuring the film thickness on the vertical sidewalls. The effects of postdeposition annealing are studied as well. This study aims to enable effective piezoelectric actuation and sensing for MEMS sensors. The conformal coverage of the ALA ALD process is excellent and AlN has the best crystal quality and degree of orientation when deposited on Al. The as-deposited films contain oxygen impurities, which might be detrimental to the piezoelectric properties of AlN. Annealing at high temperatures reduced the number of impurities but did not improve the crystal quality.

5 December 2022 in IEEE Transactions on Electron Devices
Verified
Journal Article
Open access
NTNikhilendu Tiwary
Nikhilendu Tiwary
GRGlenn Ross
Glenn Ross
VVVesa Vuorinen
Vesa Vuorinen
Mervi M. Paulasto-KröckelMervi M. Paulasto-Kröckel
Mervi M. Paulasto-Kröckel
Continuous scaling of package architectures requires small volume and high-density microbumps in 3D stacking, which often result in solders fully transforming to intermetallic compounds (IMCs). Cu–Sn solid–liquid interdiffusion (SLID) bonding is an attractive technology where the $\mu$ bumps are fully composed of IMCs. In this work, test structures made up of Cu $_{\text{3}}$ Sn IMC $\mu$ bump with a lateral dimension of 25 $\mu$ m $\times$ 25 $\mu$ m and 50 $\mu$ m $\times$ 50 $\mu$ m, respectively, were manufactured on a pair of 4-inch Si wafers demonstrating wafer-level bonding capability. Electromigration (EM) tests were performed for accelerated conditions at a temperature of 150 $^{\circ}$ C for various current densities ranging from $\approx $ 2 $\times$ 10 $^{\text{4}}$ to $\text{1}$ $\times$ 10 $^{\text{5}}$ A/cm $^{\text{2}}$ . Scanning electron microscopy (SEM) and elemental dispersive spectroscopy (EDS) were employed to characterize the as-fabricated test structures. Due to Sn squeeze out, Cu $_{\text{3}}$ Sn was formed at undesired location at the upper Cu trace. Both nondestructive lock-in thermography (LiT) and destructive techniques were employed to analyze the failure locations after EM tests. It was observed that the likelihood of failure spots is the current crowding zone along the interconnects in 3D architectures, which gets aggravated due to the formation of Cu $_{\text{3}}$ Sn in undesirable locations. Thermal runaway was observed even in Cu $_{\text{3}}$ Sn, which has been shown to be EM-resistant in the past, thus underlining inherent design issues of $\mu$ bumps utilizing SLID technology.

22 August 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Open access
SLShenyi Liu
Shenyi Liu
VVVesa Vuorinen
Vesa Vuorinen
XLXing Liu
Xing Liu
OFOlli Fredrikson
Olli Fredrikson
SBSebastian Brand
Sebastian Brand
Mervi M. Paulasto-KröckelMervi M. Paulasto-Kröckel
Mervi M. Paulasto-Kröckel
The die-attach layer is a vulnerable structure that is important to the reliability of an insulated-gate bipolar transistor (IGBT) module. A new failure mechanism named fatigue crack network (FCN) has been identified in the central area of the IGBT modules’ solder layer. In this article, to investigate the formation mechanism of the FCN, a fast power cycling test (PCT) (current on 0.2 s and current off 0.4 s) was designed and performed on a commercial IGBT module. Subsequently, scanning acoustic microscopy and X-ray imaging were used for nondestructive inspection of the defects of the solder layer. The cross section was based on the nondestructive inspection results. Then, electron backscattered diffraction analysis was carried out on both observed vertical and horizontal cracks. As a result, both networked vertical cracks at the center and horizontal cracks at the edge of the solder layer were detected. The recrystallization occurred during the PCT. The voids and cracks emerged at high-angle grain boundaries. A finite element simulation was performed to understand the driving force of FCN qualitatively. The stress simulation results indicate that under time-dependent multiaxial stress at the center of the solder, the defects nucleated, expanded, and connected vertically to form the FCNs.

15 February 2021 in Journal of Microelectromechanical Systems
Verified
Journal Article
Open access
KBKristina Bespalova
Kristina Bespalova
EOElmeri Osterlund
Elmeri Osterlund
GRGlenn Ross
Glenn Ross
Mervi M. Paulasto-KröckelMervi M. Paulasto-Kröckel
Mervi M. Paulasto-Kröckel
ASAbhilash Thanniyil Sebastian
Abhilash Thanniyil Sebastian
TPTuomas Pensala
Tuomas Pensala
Scandium-alloyed aluminum nitride (AlScN) is a potential material for micro-electromechanical systems because of its unique advantages, such as strong piezoelectric effect and high thermal stability. However, issues related to its stability and interaction with other materials in multilayer systems require investigation. The formation of new phases at the interface between piezomaterial and electrode material can lead to the device failure. In this study, multilayer structures Si substrate/AlN/Ti-Mo/Al 0.8 Sc 0.2 N/top electrode (TE) were studied after annealing at a wide range of temperatures and durations. Four different TE materials (i.e. Al, AlSi (1%), Mo/Al, and Mo) were examined to determine the most reliable electrode material for the structure. The phase stability, interfacial quality, and piezoelectric response of the multilayer systems after thermal annealing were investigated. The structure with Mo TE layer was stable after annealing at 800 °C for 300 h and at 1000 °C for 100 h. None of the structures formed any new phases at the interface between the electrode layer and AlScN. The transverse piezoelectric coefficient (e 31,f ) was determined for Al 0.8 Sc 0.2 N before and after annealing. The absolute value of the e 31,f was -1.39 C/m 2 for as-deposited structure and -1.67 C/m 2 for the same structure annealed for 300 h at 800 °C. [2020-0361]

1 September 2022 in Scripta Materialia
Verified
Journal Article
Open access
OGObert Golim
Obert Golim
VVVesa Vuorinen
Vesa Vuorinen
GRGlenn Ross
Glenn Ross
TWTobias Wernicke
Tobias Wernicke
MPMarta Pawlak
Marta Pawlak
Mervi M. Paulasto-KröckelMervi M. Paulasto-Kröckel
Mervi M. Paulasto-Kröckel

25 April 2022 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Open access
NTNikhilendu Tiwary
Nikhilendu Tiwary
VVVesa Vuorinen
Vesa Vuorinen
GRGlenn Ross
Glenn Ross
Mervi M. Paulasto-KröckelMervi M. Paulasto-Kröckel
Mervi M. Paulasto-Kröckel
Solid-liquid interdiffusion (SLID) bonding finds a wide variety of potential applications towards die-attach, hermetic encapsulation of MEMS devices and 3D heterogeneous integration. Unlike soft soldering technique, the solidification of intermetallic compound (IMC) formation in SLID bonding occurs during the process isothermally, making it difficult to predict and mitigate the sources of process-dependent thermomechanical stresses. Literature reports two dominant factors for the built-in stress in SLID bonds: volume shrinkage (due to IMC formation) and CTE mismatch. This work provides a detailed investigation of the Cu-Sn SLID bonding process by FE simulations. Specifically, the FE simulation of the SLID bonding process is divided into three steps: ramp-up, hold-time and ramp-down stages to understand the stresses formed due to each individual step. Plastic material properties for Cu as well as temperature dependent material parameters for different entities are assigned. Process-dependent thermomechanical stresses formed during the ramp-up and hold-time steps (IMC formation) were found not to be significant. The hold-time step is governed by the reaction and diffusion kinetics which determines the bond line quality including defects, such as voids. The ramp-down step is the dominant phase influencing the final stress formations in the bonds. The results show an average of >30% decrease in the stress levels in Cu3Sn layer (IMC) when the bonding temperature is brought down from 320 °C to 200 °C, thus demonstrating the importance of low temperature SLID process.