The modification method of aluminosilicate clays and the modifier content have a decisive influence on the structure and properties of the obtained nanocomposites. Therefore, the development and research of new techniques of nanoclays modification are of great importance for polymer nano-chemistry. The work studied the modification of montmorillonite (MMT) using polyvinylpyrrolidone (PVP) in an aqueous colloidal solution with the subsequent separation of three separate fractions of the solution according to the previously developed method. The influence of the initial mass ratio of components (MMT/PVP) on the structure and thermal properties of the modified MMT in each solution layer was determined. Scanning electron microscopy (SEM), X-ray diffraction (XRD), thermal gravimetry (TG), differential scanning calorimetry (DSC), and Fourier-transform infrared (FTIR) spectroscopy were used for research. It was established that the mass ratio of components in the initial solution has almost no effect on the structure of MMT in the top and middle solution layers, but significantly affects the yield of final products. Different structures can be obtained in the bottom layer of the solution. Still, intercalated MMT was obtained exclusively at the mass ratio of MMT/PVP = 1:2. In addition, the work investigated the structure and thermal properties of modified montmorillonites with the same PVP content, and it has been proven that such composites have dissimilar structures and properties when obtained by different methods.
The effect of the new bioproduct in the form of granulate and liquid concentrate on PLA biodegradation during industrial composting was investigated. The analysis included compost parameters, PLA mass loss, structural changes (SEM) and chemical properties (FTIR-ATR, O/C ratio). The effectiveness of the bioproduct, especially in liquid form, in accelerating PLA degradation and improvingcompost properties was confirmed what matters for sustainable waste management.
3 July 2025 in Beilstein Journal of Nanotechnology
Recent advances in nanocomposite technology, particularly the incorporation of carbon nanotubes, have shown promise in enhancing the properties of biodegradable polymers. This study investigated the effect of a 0.5 wt % addition of multiwalled carbon nanotubes (MWCNTs) on the properties of bio-poly(butylene succinate) (BioPBS) using a masterbatch-based melt compounding method. The incorporation of MWCNTs enhanced the mechanical strength and stiffness, improved the tribological properties by reducing friction, and increased the crystallization temperature. However, it also resulted in a decrease in elasticity. Morphological analysis confirmed the uniform dispersion of the nanotubes. These findings underscore the potential of MWCNTs to tailor the properties of BioPBS for specific applications, such as in the packaging, automotive, and biomedical industries, where both biodegradability and enhanced material performance are desirable.
1 April 2024 in Advances in Science and Technology Research Journal
The use of carbon nanomaterials as fillers in the process of obtaining polymer composites by extrusion poses many problems. The high agglomeration ability and low bulk density of carbon nanomaterials do not allow to easy production of composites characterized by very good dispersion of the filler...
The paper presents studies on the use of waste from wind turbine blades (WTBs) in the production of thermoplastic composites and regranulate-based products of acrylonitrile-butadiene-styrene (ABS) copolymers. Composites containing two types of WTB fractions (finely milled fraction—GRm and dust fraction—GRd) were produced using a co-rotating twin-screw extruder. During extrusion, different screw configurations of the plasticizing system as well as different material formulations were investigated. The studied composites contained from 10 to 70 wt% of shredded WTB, as well as up to 15 wt% of additional components, mainly those improving impact strength and processing properties. It was found that the individual WTB fractions generally deteriorate the mechanical properties of ABS. However, a composite containing 30 wt% GRm and modified with an additional 7 wt% ACM-G2 (impact modifier type) can be hot-pressed into good quality panels. It can also be successfully used to produce profiles in the extrusion process, mainly due to its significantly reduced viscosity. The studies presented in this article showed one of the possible ways of using WTB waste. It is advantageous because it uses WTB waste in a thermoplastic ABS matrix, which is also a secondary raw material. As a consequence of this, a completely new composite material based wholly on secondary raw materials can be obtained, which can be subjected to multiple processing.
This study analyzes the effect of two bioactive additives—caffeic acid and natamycin (Natamax®)—on the properties of poly(butylene succinate) (PBS) in the context of applications in biodegradable active packaging. Materials containing 1, 3, and 5 wt.% of the additives were prepared by melt blending and characterized in terms of density, rheological behavior (MFR), mechanical properties, thermal stability (TGA), and thermal behavior and crystallization (DSC). Caffeic acid strongly reduced the melt viscosity (reflected by a significant increase in MFR) and, at higher concentrations, led to material stiffening and increased strength at the expense of a pronounced reduction in deformability. Natamycin exhibited a milder rheological effect; at 1 wt.% it simultaneously improved strength and elastic modulus, whereas at higher loadings it deteriorated mechanical performance due to structural effects. Both additives were thermally compatible with PBS; caffeic acid introduced an additional degradation step, while Natamax® did not significantly alter the degradation mechanism. The results indicate that both the type and concentration of the additive govern the structure–property–function relationships and enable the design of PBS-based packaging materials with controlled performance and functional characteristics.