Mukhtar Ahmad

Mukhtar Ahmad

Auto-generated profile, based on publicly available information

Mukhtar Ahmad

Faculty of Engineering, Free University of Bozen-Bolzano, Bozen-Bolzano 39100, Italy

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2023 in Flexible and Printed Electronics
Verified
Journal Article
Open access
SVSahira Vasquez
Sahira Vasquez
MAMartina Aurora Costa Angeli
Martina Aurora Costa Angeli
Mattia PetrelliMattia Petrelli
Mattia Petrelli
MAMukhtar Ahmad
Mukhtar Ahmad
BSBajramshahe Shkodra
Bajramshahe Shkodra
LPLuisa Petti
Luisa Petti
Even though a plethora of printing technologies are currently available and their potential for the fabrication of low-cost and flexible sensors has been widely investigated, systematically based, and statistically sustained comparative studies are missing in the literature. In this work, we compare screen, inkjet, and dispense printing for the fabrication of carbon nanotube (CNT)-based ammonia (NH3) chemiresistive flexible gas sensors for the first time. Moreover, we report the first CNT-based gas sensor fabricated via Voltera printer. The devices were made of a thin layer of spray-coated CNTs and printed silver-based interdigitated electrodes. To draw a thoughtful comparison the same sensor layout, materials, and fabrication flow were used. The device morphological features were acquired through microscopic, atomic force microscope, and 3D images; additionally, the response to NH3 as well as the printing process characteristics for each technique was analyzed. From 300 µm nominal spacing between lines, we obtained a decrease of 25%, 13%, and 5% on the printed spacings with dispense, screen, and inkjet printing, respectively. At 100 ppm of NH3, a maximum response of 33%, 31%, and 27% with the dispense-, inkjet-, and screen-printed sensors were found, respectively. Statistical differences were observed between the mean values on the NH3 response of dispense- compared to the inkjet- and screen-printed sensors, which in effect showed the highest response in the Tukey test. This demonstrated that the fabrication technique employed can induce a different response mainly driven by the printed outcomes. Following a holistic approach that includes the sensor response, the application, the market perspective, and the process versatility, we suggest screen printing as the most suitable method for CNT-based NH3 gas sensor fabrication.

27 July 2022 in IEEE Transactions on Electron Devices
Verified
Journal Article
Open access
FCFederica Catania
Federica Catania
MAMukhtar Ahmad
Mukhtar Ahmad
DCDianne Corsino
Dianne Corsino
NKNiloofar Saeedzadeh Khaanghah
Niloofar Saeedzadeh Khaanghah
LPLuisa Petti
Luisa Petti
GCGiuseppe Cantarella
Giuseppe Cantarella
Transparent transistors are mainly investigated in view of their integration in displays and their employment in wearable electronics where the integration of flexible and imperceptible systems is an important requirement. Here, the fabrication and ac performance of flexible InGaZnO thin-film transistors (TFTs) and circuits are presented to evaluate their suitability for analog sensor conditioning applications. Functional oxides are employed to guarantee the transparency of the device, while their fabrication processes are suitable to directly realize electronics on a flexible polyimide substrate. The TFTs show state-of-the-art performance with a field-effect mobility $\mu _{\text {eff}}\,\,= {19}.{39}\,\, \text {cm}^{{2}} \text {V}^{-1} \text {s}^{-1}$ and functionality while bent to radii as low as 5 mm. Reliable scattering parameters measurements confirm transit frequencies as high as $f_{t}~\approx ~7.84$ MHz. Simultaneously, nMOS ring oscillators (ROs) show functionality at supply voltage ${V} _{\text {DD}}$ ranging from 1.75 to 12.25 V with a maximum oscillation frequency ${f} _{\text {osc}}\,\,=132.9$ kHz. Finally, common-source amplifiers (CSAs) exhibit the voltage gains up to 10.7 dB, the cutoff frequencies up to 10.8 kHz, and a power consumption down to $4.4~\mu \text{W}$ .

16 June 2023 in Advanced Engineering Materials
Verified
Journal Article
Open access
MAMukhtar Ahmad
Mukhtar Ahmad
MAMartina Aurora Costa Angeli
Martina Aurora Costa Angeli
PIPietro Ibba
Pietro Ibba
SVSahira Vasquez
Sahira Vasquez
BSBajramshahe Shkodra
Bajramshahe Shkodra
LPLuisa Petti
Luisa Petti
Printing technologies have emerged as a viable method for the fabrication of various electronic components, including sensors, actuators, energy harvesters, thin‐film transistors and circuits, as well as antennas. However, printing processes have limitations in terms of surface roughness and thickness. Printing conductive structures on novel substrates, such as cellulose‐based sustainable paper, also leads to further challenges linked to the high surface porosity and ink carrier absorption. Herein, the variability of paper‐based printed antenna performance due to different printing processes, ink carrier absorption, and temperature is investigated. The resonance frequency and gain of different printed antennas (e.g., screen, inkjet, and dispense‐printed) are compared in terms of surface roughness, thickness, and resonance frequency. Screen‐printed antennas show better performance compared to other printed antennas. The results show that the resonance frequency of antenna shifts 20, 30, and 50 MHz for screen printed, dispense printed, and inkjet printed respectively, from the nominal 2.6 GHz. In the case of the inkjet‐printed antenna, a clear effect of skin depth is observed, due to the 0.91 thickness. Furthermore, it is demonstrated that the permittivity/dielectric constant of the paper substrate is significantly influenced by ink carrier absorption and temperature variance.

19 December 2025 in Journal of Physics: Materials
Verified
Journal Article
Open access
ANAnnelot Nijkoops
Annelot Nijkoops
MCManuela Ciocca
Manuela Ciocca
MAMartina Aurora Costa Angeli
Martina Aurora Costa Angeli
MAMukhtar Ahmad
Mukhtar Ahmad
RBRemko Boom
Remko Boom
LPLuisa Petti
Luisa Petti
Conducting polymers (CPs) are highly susceptible to ammonia ( NH 3 ) at room temperature. This has spurred growing interest in CP-based NH 3 gas sensors across diverse fields, ranging from biomedicine to environmental monitoring. Detecting NH 3 levels in breath, from parts per million to parts per billion, aids in diagnosing health conditions like liver and kidney dysfunction. Despite the importance of CP-based NH 3 sensors, a comprehensive assessment of their performance, limitations, and prospects has yet to be conducted. To address this gap, this work provides a detailed review of chemiresistive NH 3 sensors based on CPs (including P3HT, PEDOT, PPy, and PANI), examining sensor response, selectivity, stability, repeatability, and sensitivity to environmental factors like humidity and temperature. The role of porous structures and gas diffusion mechanisms in enhancing CP sensor performance is emphasized, alongside CP-based composite materials. The mechanical flexibility of these sensors is analyzed and compared, highlighting their potential for integration into flexible and wearable devices. Key challenges for CP-based NH 3 sensors include poor selectivity due to interference from similar gases, sensitivity loss caused by humidity-induced CP swelling, and instability from temperature fluctuations. Additionally, the lack of standardized testing protocols complicates performance comparisons of CP-based NH 3 sensors. Future research should focus on improving CP porosity, understanding gas-CP interactions, developing stable composites, and exploring new CPs for improved NH 3 sensing.