14 August 2018 in IEEE Journal of Solid-State Circuits
A 24-72-GS/s 8-b time-interleaved analog-to-digital converter (ADC) is presented which exceeds 39-dB SNDR at low input frequency and 30-dB SNDR at Nyquist. High SNDR at Nyquist is achieved by 16 parallel sampling switches driven by short clock pulses. Clock-pulse edges can be shifted digitally to reduce the impact of timing mismatch. A total of 64 asynchronous 8-b successive approximation (SAR) ADCs at low supply voltage convert sampled voltages. The SAR ADCs use a differential capacitive DAC, one comparator per decision, and include a reference voltage DAC and buffer. The ADC consumes 2.0 pJ/conversion at 48 GS/s and 3.3 pJ/conversion at 72 GS/s and is implemented in 14-nm CMOS FinFET on 0.15 mm².
23 September 2019 in IEEE Journal of Solid-State Circuits
This article introduces a wireline receiver (RX) data-path employing discrete multi-tone (DMT) modulation for communicating over electrical links. The DMT RX incorporates a fully digital equalization data-path, with a synthesized and automatically placed and routed digital signal processor (DSP) following a 10-bit time-interleaved pipelined successive-approximation register analog-to-digital converter (TI-PISAR ADC). The prototype RX chip implemented in a 14-nm FinFET process demonstrates a lane data rate of 56 Gb/s dissipating 161 mW including the ADC and the DSP power. The energy efficiency of 1.2 pJ/b for the DSP and 2.9 pJ/b for the entire RX was achieved with the data-rate of 56 Gb/s for communicating over channels exhibiting up to 28-dB loss at 14 GHz with a bit-error-rate (BER) better than 2e-4.
21 August 2014 in IEEE Journal of Solid-State Circuits
A 16 Gb/s I/O link receiver fabricated in 22 nm CMOS SOI technology is presented. Attenuation and ISI of transmitted NRZ data across PCB channels are equalized with a CTLE feeding an 8-tap DFE. The first tap uses digital speculation and the following seven taps are realized by means of the switched-capacitor technique. Timing recovery and control are performed with a Mueller-Müller type-A baud-rate CDR. The architecture is half-rate and requires one phase rotator. In total, each slice has six comparators to recover data and timing information. The secondorder digital CDR operates at quarter-rate and features a low-latency implementation of the proportional path. At 16 Gb/s, 1 Vppd PRBS31 data transmitted without FFE equalization is recovered across a PCB channel with 34 dB attenuation at 8 GHz. The measured tracking bandwidth is 31 kppm (16 GHz ± 496 MHz), and an amplitude of 3 UIPP is tolerated at 1 MHz sinusoidal jitter. The sinusoidal jitter amplitude tolerance measured at 10 Gb/s is 0.4 UIPP at 10 MHz and remains above 0.2 UIPP up to 1 GHz with PRBS31 data recovered (BER <; 10 -12 ) across a PCB channel with 27 dB attenuation at 5 GHz. The power efficiency is 3.7 mW/Gb/s, including the full-rate clock receiver.
11 February 2016 in IEEE Transactions on Power Electronics
The operation and efficiency of on-chip switched-capacitor (SC) converters are highly affected by the parasitic bottom plate capacitor present in on-chip capacitor technologies. Existing modeling frameworks do not in a comprehensive manner take the effect of the bottom plate capacitor on converter operation and efficiency into account. This paper extends an existing SC state space modeling framework to include the bottom plate capacitor. The developed model is used in a Pareto optimization procedure to optimally select the component values of a 2:1 on-chip SC converter. Implemented in a 32 nm SOI CMOS technology that features the high-density deep trench capacitor, the on-chip converter achieves 86% maximum efficiency at 4.6 W/mm2 power density while converting from a 1.8 V input voltage to 830 mV output voltage.
29 August 2018 in IEEE Journal of Solid-State Circuits
A single-channel 12-bit SAR ADC achieving 250–340 MS/s and consuming 4.8–8.0 mW from 0.75 to 0.9 V is presented. At 300 MS/s, the ADC exhibits 61.6-dB peak SNDR and reaches 60.5-dB SNDR and 78.7-dB SFDR with 0.8- $\text{V}_{\text {pp, diff}}$ input amplitude at Nyquist. It consumes 7.0 mW from a single 0.85-V supply, where 3.7 mW is contributed by the reference buffer. The key element is a comparator with an inverter-based preamplifier to achieve low-noise performance with below 1- $\text{V}_{\text {pp, diff}}$ input amplitude. The common-mode (CM) sensitivity of the inverter is counteracted by an SAR-based CM regulation (CMREG). The regulation adjusts the sampled CM to the optimal CM for the maximum inverter gain using a second capacitive DAC. It adjusts the CM on a sample-by-sample basis and, thus, can correct time-varying CM. The implemented CMREG maintains SNDR above 60 dB for a differential input amplitude mismatch of up to 2 dB or a phase mismatch of up to 15°.
19 March 2018 in IEEE Transactions on Circuits and Systems I: Regular Papers
The implementation of a 25.6-Gb/s four-level pulse-amplitude-modulation (4-PAM) reduced-state sliding-block Viterbi detector (VD) is presented. The power consumption of the VD is 105,mW at a supply voltage of 0.7 V, corresponding to an energy efficiency of 4.1 pJ/b. A data rate of 30.4 Gb/s is achieved with an energy efficiency of 5.3 pJ/b at a supply voltage of 0.8 V. The VD, implemented in an experimental chip fabricated in 14-nm CMOS FINFET, exploits set-partitioning principles and embedded per-survivor decision feedback to reduce implementation complexity and power consumption. The active area of the VD with 12 slices, each operating at one-eighth of the modulation rate, is 0.507 x 0.717 mm². Experimental results showing system performance are obtained by using a (2¹⁵ - 1)-bit pseudo-random binary sequence. The impact of the synchronization length and survivor path memory length on the detector design and system performance are shown. A new pipelined reduced-state sequence detector algorithm is presented for high-speed implementations. A novel speculative symbol timing recovery scheme is proposed. New simulation results are obtained to compare the performance of the Reed-Solomon (RS)-encoded 4-PAM scheme with that of the concatenated RS 4-D 5-PAM trellis-coded-modulation (TCM) scheme over an ideal band-limited additive-white-Gaussian-noise channel. Drawing on the results achieved for the VD, novel design techniques for a high-speed low-complexity eight-state 4-D 5-PAM TCM decoder is proposed.