5 March 2019 in IEEE Electron Device Letters
3 March 2017 in ECS Journal of Solid State Science and Technology
A self-aligned Nickel (Ni) silicide process (Salicide) for n-type ohmic contacts on 4H-SiC is demonstrated and electrically verified in a wafer-scale device process. The key point is to anneal the contacts in two steps. The process is successfully employed on wafer-level and a contact resistivity below 5 × 10−6 Ω·cm2 is achieved. The influence of the proposed process on the oxide quality is investigated and no significant effect is observed. The proposed self-aligned technology eliminates the undesirable effects of the lift-off process. Moreover, it is simple, fast, and manufacturable at wafer-scale which saves time and cost.
5 June 2018 in Materials Science Forum
Most semiconductor devices require low-resistance ohmic contact to p-type doped regions. In this work, we present a semi-salicide process that forms low-resistance contacts (~10-4 Ω cm2) to epitaxially grown p-type (>5×1018 cm-3) 4H-SiC at temperatures as low as 600 °C using rapid thermal processing (RTP). The first step is to self-align the nickel silicide (Ni2Si) at 600 °C. The second step is to deposit aluminium on top of the silicide, pattern it and then perform a second annealing step in the range 500 °C to 700 °C.
27 September 2023 in Materials Science in Semiconductor Processing
20 March 2017 in Journal of Electronic Materials
4H-SiC electronics can operate at high temperature (HT), e.g., 300°C to 500°C, for extended times. Systems using sensors and amplifiers that operate at HT would benefit from microcontrollers which can also operate at HT. Microcontrollers require nonvolatile memory (NVM) for computer programs. In this work, we demonstrate the possibility of integrating ferroelectric vanadium-doped bismuth titanate (BiTV) thin films on 4H-SiC for HT memory applications, with BiTV ferroelectric capacitors providing memory functionality. Film deposition was achieved by laser ablation on Pt (111)/TiO2/4H-SiC substrates, with magnetron-sputtered Pt used as bottom electrode and thermally evaporated Au as upper contacts. Film characterization by x-ray diffraction analysis revealed predominately (117) orientation. P–E hysteresis loops measured at room temperature showed maximum 2P r of 48 μC/cm2, large enough for wide read margins. P–E loops were measurable up to 450°C, with losses limiting measurements above 450°C. The phase-transition temperature was determined to be about 660°C from the discontinuity in dielectric permittivity, close to what is achieved for ceramics. These BiTV ferroelectric capacitors demonstrate potential for use in HT NVM applications for SiC digital electronics.
12 February 2019 in Journal of Electronic Materials
Previous studies showed that cobalt silicide can form ohmic contacts to p-type 6H-SiC by directly reacting cobalt with 6H-SiC. Similar results can be achieved on 4H-SiC, given the similarities between the different silicon carbide polytypes. However, previous studies using multilayer deposition of silicon/cobalt on 4H-SiC gave ohmic contacts to n-type. In this study, we investigated the cobalt silicide/4H-SiC system to answer two research questions. Can cobalt contacts be self-aligned to contact holes to 4H-SiC? Are the self-aligned contacts ohmic to n-type, p-type, both or neither? Using x-ray diffraction, it was found that a mixture of silicides (\(\hbox {Co}_2\hbox {Si}\) and CoSi) was reliably formed at 800\(^\circ \)C using rapid thermal processing. The cobalt silicide mixture becomes ohmic to epitaxially grown n-type (\(1\times 10^{19} \hbox {cm}^{-3}\)) if annealed at 1000\(^\circ \)C, while it shows rectifying properties to epitaxially grown p-type (\(1\times 10^{19} \hbox {cm}^{-3}\)) for all tested anneal temperatures in the range 800–1000\(^\circ \)C. The specific contact resistivity (\(\rho _\mathrm{C}\)) to n-type was \(4.3 \times 10^{-4}\) \(\mathrm {\Omega }\) \(\,\hbox {cm}^{2}\). This work opens the possibility to investigate other self-aligned contacts to silicon carbide.