Uğur Kölemen

Uğur Kölemen

Auto-generated profile, based on publicly available information

Uğur Kölemen

Department of Physics, Faculty of Arts and Sciences, University of Tokat Gaziosmanpasa, Tokat, Türkiye

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

24 November 2017 in Isotopes in Environmental and Health Studies
Verified
Journal Article
Closed access
ITİbrahim Türkekul
İbrahim Türkekul
CYCafer Mert Yeşilkanat
Cafer Mert Yeşilkanat
ACAli Ciriş
Ali Ciriş
UKUğur Kölemen
Uğur Kölemen
UÇUğur Çevik
Uğur Çevik
The activity concentration of natural (238U, 232Th, and 40K) and artificial (137Cs) radionuclides was determined in 50 samples (obtained from the same station) from various species of mushrooms and soil collected from the Middle Black Sea Region (Turkey). The activities of 238U, 232Th, 40K, and 137Cs were found as 84 ± 16, 45 ± 14, 570 ± 28, and 64 ± 6 Bq kg–1 (dry weight), respectively, in the mushroom samples and as 51 ± 6, 41 ± 6, 201 ± 11, and 44 ± 4 Bq kg–1, respectively, in the soil samples for the entire area of study. The results of all radionuclide activity measurements, except those of 238U and 232Th in the mushroom samples, are consistent with previous studies. In the soil samples, the mean values of 238U and 232Th are above the world mean, and the activity mean of 40K is below the world mean. Finally, the activity estimation was made with both the soil and mushroom samples for unmeasured points within the study area by using the ordinary kriging method. Radiological distribution maps were generated.

2 September 2025 in Physica Scripta
Verified
Journal Article
Closed access
CTCengiz Temiz
Cengiz Temiz
FYFikret Yilmaz
Fikret Yilmaz
SÇSeyit Çağlar
Seyit Çağlar
UKUğur Kölemen
Uğur Kölemen
OUOrhan Uzun
Orhan Uzun
In this study, to improve the mechanical properties of 2xxx series Al-5Cu alloy, 0.5% and 1.0% Sc doped Al-5Cu alloys were produced, and these alloys were processed by induction melting with a low cooling rate and melt spinning with a high cooling rate. The chemical compositions of the alloys were confirmed by XRF analysis, and XRD analysis showed the presence of α-Al and θ-Al2Cu phases in the ingot Al-5Cu alloy and Cu2Sc phase in the Sc-doped alloys. The same phases were observed in the ribbon alloys produced by rapid solidification, but the degree of crystallization and lattice stress were higher. SEM-EDX analysis revealed that the ribbon alloys have finer grain sizes, while Rietveld analysis showed that the Cu2Sc phase increases with the amount of Sc. DSC analyses confirmed the melting/solidification peak of the α-Al phase and the small peaks of the θ-Cu2Al phase, and it was also determined that the addition of Sc decreased the enthalpy of solidification of the α-Al phase. In the ribbon alloys produced by melt spinning, it was observed that the grain size was reduced, but the effect of Sc was limited to high cooling rates. The microstructure of the ribbon alloys showed finer grains on the disk surface, explaining the rapid heat removal from the melt. As a result, it is understood that Sc doping improves the mechanical properties of ribbon alloys obtained by rapid solidification, but its effect is limited in some cases.

30 June 2021 in Sakarya University Journal of Science
Verified
Journal Article
Closed access
ÖBÖznur Bağ
Öznur Bağ
FYFikret Yilmaz
Fikret Yilmaz
UKUğur Kölemen
Uğur Kölemen
SESemra Ergen
Semra Ergen
In this study, the effects of Zr addition on phase transformation temperatures, microstructure of Ti-12V-4Al (wt. %) high temperature shape memory alloys (HTSMAs) manufactured using melt-spinning technique were investigated. During heating, differential scanning calorimetry (DSC) curves showed that austenite transformation temperature of Ti-12V-4Al (wt. %) melt-spun ribbon was single-stage transformation and Ti-12V-4Al-0.5Zr (wt. %) melt-spun ribbon was two-stage transformation. In the scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyzes, unveiled that the melt-spun ribbons consisted of martensite, austenite and R phases. Transmission electron microscopy (TEM) analysis showed that the thickness of martensite plates in ribbons was thinned by the addition of Zr.