Fikret Yilmaz

Prof. Dr. Fikret Yilmaz


Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2011 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
IKIlker Kucuk
Ilker Kucuk
MAMuratahan Aykol
Muratahan Aykol
OUOrhan Uzun
Orhan Uzun
MYMehmet Yildirim
Mehmet Yildirim
MKMehmet Kabaer
Mehmet Kabaer
AMAmdulla O. Mekhrabov
Amdulla O. Mekhrabov

1 November 2018 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
FYFikret Yilmaz
Fikret Yilmaz
SESemra Ergen
Semra Ergen
SHSoon-Jik Hong
Soon-Jik Hong
OUOrhan Uzun
Orhan Uzun

30 June 2013 in Materials Characterization
Verified
Journal Article
Closed access
SESemra Ergen
Semra Ergen
OUOrhan Uzun
Orhan Uzun
FYFikret Yilmaz
Fikret Yilmaz
MKM. Fatih Kiliçaslan
M. Fatih Kiliçaslan

1 January 2021 in Solid State Communications
Verified
Journal Article
Closed access
ÖBÖznur Bağ
Öznur Bağ
SESemra Ergen
Semra Ergen
FYFikret Yilmaz
Fikret Yilmaz
UKUğur Kölemen
Uğur Kölemen

2 September 2025 in Physica Scripta
Verified
Journal Article
Closed access
CTCengiz Temiz
Cengiz Temiz
FYFikret Yilmaz
Fikret Yilmaz
SÇSeyit Çağlar
Seyit Çağlar
UKUğur Kölemen
Uğur Kölemen
OUOrhan Uzun
Orhan Uzun
In this study, to improve the mechanical properties of 2xxx series Al-5Cu alloy, 0.5% and 1.0% Sc doped Al-5Cu alloys were produced, and these alloys were processed by induction melting with a low cooling rate and melt spinning with a high cooling rate. The chemical compositions of the alloys were confirmed by XRF analysis, and XRD analysis showed the presence of α-Al and θ-Al2Cu phases in the ingot Al-5Cu alloy and Cu2Sc phase in the Sc-doped alloys. The same phases were observed in the ribbon alloys produced by rapid solidification, but the degree of crystallization and lattice stress were higher. SEM-EDX analysis revealed that the ribbon alloys have finer grain sizes, while Rietveld analysis showed that the Cu2Sc phase increases with the amount of Sc. DSC analyses confirmed the melting/solidification peak of the α-Al phase and the small peaks of the θ-Cu2Al phase, and it was also determined that the addition of Sc decreased the enthalpy of solidification of the α-Al phase. In the ribbon alloys produced by melt spinning, it was observed that the grain size was reduced, but the effect of Sc was limited to high cooling rates. The microstructure of the ribbon alloys showed finer grains on the disk surface, explaining the rapid heat removal from the melt. As a result, it is understood that Sc doping improves the mechanical properties of ribbon alloys obtained by rapid solidification, but its effect is limited in some cases.

10 November 2021 in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
Verified
Journal Article
Closed access
PDF file
CTCengiz Temiz
Cengiz Temiz
FYFikret Yilmaz
Fikret Yilmaz
UKUğur Kölemen
Uğur Kölemen
Al-5Cu, 2xxx serisi Al-esaslı alaşım grubundan olup hafif ağırlığın gerektirdiği otomotiv ve havacılık endüstrisinde geniş bir kullanım alanına sahiptir. Al-5Cu alaşımlarının en belirgin özellikleri, düşük yoğunluk, yüksek erime sıcaklığı, iyi termal iletkenlik, yüksek dayanım ve tokluktur. Bu araştırmada, Al-5Cu alaşımının mekanik özelliklerinin geliştirilmesi amaçlanmıştır. Bu sebeple, ağ.% 0.5 ve 1.0 oranında Skandiyum (Sc) katkılı Al-5Cu alaşımı indüksiyonla ergitme yöntemi ile üretilmiştir. X-ışınımı kırınımı (XRD) analizlerinden, Al-5Cu alaşımında Al ve Al2Cu fazları gözlenirken, Sc katkılı alaşımlarda bu fazların yanında Cu2Sc fazı tespit edilmiştir. Taramalı elektron mikroskobu (SEM) analizlerinden, Sc katkısının, külçe alaşımların mikro yapısını büyük oranda incelttiği görülmüş ve ayrıca, Sc katkılı alaşımlarda yarı-kararlı iğnemsi θ'-Al2Cu fazlarına rastlanılmıştır. Ayrıca alaşımlarda gözlenen mekanik özelliklerindeki iyileşme, tane boyutu sertleşmesi ve çökelti sertleşmesi mekanizmaları ile açıklanmıştır. Nano çentme testi sonuçlarından, Sc elementinin Al-5Cu alaşımını mekanik özellikleri bakımından büyük oranda geliştirdiği anlaşılmıştır.