This paper presents a passivity-based control (PBC) scheme for the Switched Reluctance Generator (SRG) in small-scale wind energy conversion systems (WECSs) for DC microgrid application. The main objective is to stabilize the output voltage in case the system supplies constant power loads (CPLs) and operate with maximum power point tracking (MPPT). Stability improvement and dc-link ripple reduction in the presence of CPLs is achieved using system level modeling of SRG-based DC microgrid through the Euler-Lagrange system (ELS) from the view point of the machine physical structure. Compared with other control methods, the proposed MPPT method based on passivity-based speed controller employs the back-EMF in the generation process as a position-dependent voltage source to overcome the major challenge of SRG complicated uncertain dynamic model. To deal with the time-varying inductance and back-emf of SRG, an adaptation mechanism is incorporated in proposed adaptive PBC and the control design is constructed by using the Lyapunov theorem where the closed-loop stability is ensured. The effectiveness of the proposed method in avoiding instability effects of SRG and CPL with voltage ripple reduction and precise wind turbine speed tracking is investigated with simulation results and validated with experimental by using a four-phase, 8/6 SRG drive system.
27 December 2017 in IEEE Transactions on Industrial Electronics
Modified quasi Z-source converter (MQZSC) is presented in this paper as a front end converter for the switched reluctance motor (SRM) drive system in order to perform voltage regulation and power factor correction (PFC). Using the MQZSC, magnetization voltage is increased and regulated according to the operation modes and requirements of the drive system; therefore, more power is transferred to the motor in each stroke. The demagnitization port is also decoupled from the magnetization port and boosted further to reduce demagnetization time. The proposed converter like conventional SRM converter has the freewheeling mode of operation. The peak current control (PCC) PFC is integrated into the control system of the front-end converter to reduce total harmonic distortion and enhance the power factor. Also, an angle control is implemented in the SRM drive system to reduce the torque ripple alongside voltage regulation in the front end controller. A software simulation is done to verify the proposed drive system. To demonstrate the abilities of the proposed drive system in practice, an experimental setup is devised in the laboratory to verify the simulation results.
1 January 2016 in Turkish Journal of Electrical Engineering and Computer Sciences
Selection of electrical machine is a key issue in electrical and hybrid electrical vehicles (HEVs and EVs). As far as HEVs and EVs are concerned, mechanical ruggedness of electrical machine is of utmost importance. For these reasons, the application of switched reluctance (SR) machine in EVs and HEVs is a viable option. In this study, an SR generator (SRG) has been utilised to work as a battery charger in EVs. The current ripple of the SRG is the greatest issue when it works as a battery charger. Therefore, a power converter and a smart search control (SSC) approach are proposed in this study to decrease the current ripple when the output power has a maximum quantity. During the system operation, the SSC method determines the value of excitation angle, turn‐on and turn‐off angles for each phase of SRG. The simulation and experimental results demonstrate the eligibility of the SSC system and power converter to obtain the acceptable charging current in maximum generated power during battery charging.
Permanent magnet synchronous motors (PMSMs) are suitable options for high-performance applications due to their potential of high power density and torque smoothness. Nevertheless, there are some factors affecting this feature by producing unwanted pulsating torque. One of the causes of torque ripple is the presence of harmonic components in motor back EMF. This paper has presented a multiple reference frame (MRF) method improving torque characteristic in PMSM regarding non-sinusoidal back EMF. An adaptive notch filter (ANF) was used as a current estimator which can separate needed current components. Optimal current components, obtained from Lagrange multiplier method, were regulated through PI controllers which guaranteed the desired convergence. Cogging torque and rms current minimization were intended, too. Results were investigated through simulations in Matlab/Simulink environment.
This paper presents a high-performance nonlinear controller for Switched reluctance machine (SRM), acting as a speed regulation motor drive. We use a cascaded torque control structure for torque ripple minimization. In a cascaded control structure, accurate torque control requires inner current controller. Passivity-based control (PBC) approaches is proposed for current control purpose. By using the port-controlled Hamiltonian (PCH) systems theory, a full-order nonlinear controlled model is first developed. Then nonlinear passivity-based adaptive sliding mode control algorithm in the presence of external disturbances for the purpose of torque ripple reduction and characteristic improvement is presented. The proposed controller design is separated into the inner loop and the outer loop controller. In the inner loop, passivity-based control (PBC) is employed by using energy shaping techniques to produce the proper switching function. The outer loop control is employed by adaptive sliding controller to determine the appropriate Torque command. It can also overcome the inherent nonlinear characteristics of the system and make the whole system robust to uncertainties. The performance of the proposed controller algorithm has been demonstrated in simulation and also experimentally using a 4KW, four-phase, 8/6 pole SRM DSP-based drive system.