27 December 2017 in IEEE Transactions on Industrial Electronics
SNSayed Morteza Saghaian Nejad
Sayed Morteza Saghaian Nejad
Modified quasi Z-source converter (MQZSC) is presented in this paper as a front end converter for the switched reluctance motor (SRM) drive system in order to perform voltage regulation and power factor correction (PFC). Using the MQZSC, magnetization voltage is increased and regulated according to the operation modes and requirements of the drive system; therefore, more power is transferred to the motor in each stroke. The demagnitization port is also decoupled from the magnetization port and boosted further to reduce demagnetization time. The proposed converter like conventional SRM converter has the freewheeling mode of operation. The peak current control (PCC) PFC is integrated into the control system of the front-end converter to reduce total harmonic distortion and enhance the power factor. Also, an angle control is implemented in the SRM drive system to reduce the torque ripple alongside voltage regulation in the front end controller. A software simulation is done to verify the proposed drive system. To demonstrate the abilities of the proposed drive system in practice, an experimental setup is devised in the laboratory to verify the simulation results.
19 March 2020 in IEEE Transactions on Power Electronics
Interaction of the ac-link capacitor with ac- and dc-side inductors in the Ćuk converter topology introduces resonant frequency oscillations that affect the dynamic response and performance of the converter. To mitigate these effects, in this letter, a simple passive damping-based solution is employed, which is optimized both from control perspective and power loss for an integrated-magnetics-based differential-mode Ćuk rectifier. An experimental prototype is developed to validate the effect of no damping versus optimized damping and its effects on the rectifier performance parameters are provided.
17 March 2021 in IEEE Transactions on Power Electronics
In this article, the design methodology of integrated magnetics (IM) for a three-phase differential-mode Ĉuk rectifier (DMCR) is outlined. The design and optimization of the IM are so achieved such that the inductor current ripple, total harmonic distortion of the input current, and magnetics loss are optimized without compromising the stability of the DMCR. The optimization and design of the IM are conducted using the Maxwell and SaberRD software tools, and subsequently, the results are compared with a plurality of other IM structures for performance comparison. Finally, the experimental hardware for the DMCR comprising the optimized IM is fabricated to validate its performance and compare it with a DMCR fabricated solely using discrete magnetics.
18 February 2022 in IEEE Transactions on Industry Applications
Rapid widespread vehicle electrification has incentivized fast chargers to improve their performances. In this article, an integrated-magnetic-based differential-mode Ĉuk rectifier (IM-DMCR) as a universal battery supercharger is introduced. The design challenges associated with the high-power operation of IM-DMCR are outlined, and optimized solutions are presented. A SiC-based full-scale 60 - kW experimental prototype for the IM-DMCR is built and tested to verify the design.
27 September 2023 in IEEE Transactions on Power Electronics
In this article, a novel continuous modulation scheme with variable-dc-offset (CMS-VDO) is proposed for a single-phase differential-mode inverter (DMI). The output voltage of the DMI is the difference in output voltages of two differentially connected dc–dc converters. CMS-VDO is so designed that the output voltage of the individual dc/dc converter is reduced without affecting the output voltage of the DMI. This reduced voltage yields reductions in circulating current, peak switch voltage, total harmonic distortion, and improved efficiency compared to conventional modulation scheme with fixed dc offset (CMS-FDO). The experimental results compare and validate the improved inverter performance using CMS-VDO over CMS-FDO.
6 April 2023 in IEEE Transactions on Power Electronics
Two driving performance metrics in modern power-electronic systems are power density and efficiency: usually, improvement in one result in sacrificing the other. In this article, triangular conduction mode (TCM) is used alongside integrated magnetics to achieve both performance metrics simultaneously. TCM is implemented by extending the switch current high enough to reverse direction and provide enough energy at the onset of the deadtime to discharge the parasitic capacitance of the SiC mosfet . The elevated current ripple is alleviated by distributing the rectifier low-frequency current among parallel interleaved sub-modules. Taking advantage of the symmetrical topology of the differential mode Ćuk rectifier, an integrated interleaved magnetic (IIM) structure is proposed to house all the inductors in a module. In doing so, flux cancellation technique is used between the ac-and dc-side inductors to reduce the losses and size while using a custom core structure to control the flux coupling between the interleaved windings. A step by step design algorithm is presented to manage the different types of coupling within IIM. Challenges in design, fabrication, and testing of the system are analyzed and appropriate solutions are presented in each section. The solutions are supported by mathematical analysis to optimize the power stage design and validated by circuit as well as finite element simulations. An experimental setup is assembled to test this concept and multiple time-domain and parametric results are presented for proof of the concept in rectifier mode and single module mode.