Mohammad Ebrahimi

Mohammad Ebrahimi

Auto-generated profile, based on publicly available information

Mohammad Ebrahimi

Department of Electrical and Computer Engineering, Isfahan University of Technology, Isfahan, Iran

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 June 2020 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
SMSeyed Abolfazl Mortazavizadeh
Seyed Abolfazl Mortazavizadeh
AGAhmad Ghaderi
Ahmad Ghaderi
MEMohammad Ebrahimi
Mohammad Ebrahimi
MHMasood Hajian
Masood Hajian
MEMohamad Ebrahimi
Mohamad Ebrahimi
The next generation of steering system in auto manufacturing industry would be steer-by-wire (SBW) in which mechanical connection between vehicle steering wheel and tires is removed. Numerous advantages are envisaged for this modification but there are still some under-research technical and safety-related challenges to be addressed. This paper presents a thorough review on the history of vehicle steering systems first. The structure and components of the cutting edge technology SBW system are subsequently described with the advantages and disadvantages discussed in detail. The main challenges of this system including the required motor-drives equipped with advanced controllers and reliability concerns are studied and proposed solutions presented in literate are reviewed. Finally, a projection of the future of steering systems considering driverless vehicles with integrated steering and traction systems is briefly presented.

27 December 2017 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
MMMoien Mohamadi
Moien Mohamadi
ARAmir Rashidi
Amir Rashidi
SNSayed Morteza Saghaian Nejad
Sayed Morteza Saghaian Nejad
MEMohammad Ebrahimi
Mohammad Ebrahimi
Modified quasi Z-source converter (MQZSC) is presented in this paper as a front end converter for the switched reluctance motor (SRM) drive system in order to perform voltage regulation and power factor correction (PFC). Using the MQZSC, magnetization voltage is increased and regulated according to the operation modes and requirements of the drive system; therefore, more power is transferred to the motor in each stroke. The demagnitization port is also decoupled from the magnetization port and boosted further to reduce demagnetization time. The proposed converter like conventional SRM converter has the freewheeling mode of operation. The peak current control (PCC) PFC is integrated into the control system of the front-end converter to reduce total harmonic distortion and enhance the power factor. Also, an angle control is implemented in the SRM drive system to reduce the torque ripple alongside voltage regulation in the front end controller. A software simulation is done to verify the proposed drive system. To demonstrate the abilities of the proposed drive system in practice, an experimental setup is devised in the laboratory to verify the simulation results.

31 December 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
MAMojtaba Afshar
Mojtaba Afshar
ATAhmadreza Tabesh
Ahmadreza Tabesh
MEMohammad Ebrahimi
Mohammad Ebrahimi
SKSayed Ali Khajehoddin
Sayed Ali Khajehoddin
This paper proposes and demonstrates a fault detection method to locate inter-turn short circuits (ITSCs) in the stator windings of a brushless doubly-fed induction machine (BDFIM). The detection of ITSC is important in machine health prognostics as ITSC is an early stage fault that may lead to other faults such as coil-to-coil and coil-to-ground. BDFIM consists of power and control windings in the stator that are magnetically coupled through a nested-loop rotor winding. Existing ITSC detection algorithms use rotor slot harmonics in stator current spectra as fault indicators for only conventional doubly-fed induction machines. However, these algorithms cannot be applied to BDFIM due to its different stator/rotor winding structure. The paper primarily proposes a new analytical formulation for the nested-loop rotor slot harmonics (NRSHs) as ITSC fault indicators in BDFIMs. Using NRSHs, a detection algorithm is also proposed to detect and locate ITSC in power/control windings of BDFIMs. The proposed algorithm is verified based on numerical analysis of a BDFIM using finite element method. The accuracy of the proposed fault detection algorithm is also experimentally investigated and demonstrated using a BDFIM test rig. Both numerical and experimental test results confirm effectiveness of the proposed ITSC fault detection and location algorithm.

11 July 2019 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
HMHooshang Mirahki
Hooshang Mirahki
MMMehdi Moallem
Mehdi Moallem
MEMohammad Ebrahimi
Mohammad Ebrahimi
BFbabak fahimi
babak fahimi
Surface-mounted Permanent Magnet Synchronous (SPMS) machines are widely used in applications that require low torque ripple, reduced vibration and acoustic noise. For those applications of SPMSM in which only unidirectional operation is needed, asymmetric design optimization show to have significant advantages over symmetric designs. In this paper, an analytical method based on Schwarz -Christoffel mapping is presented for asymmetrical magnet shape optimization in surface-mounted permanent magnet synchronous machine. In this method, permanent magnet is divided into finite cells so that each cell can be assigned with either air (OFF) or magnet (ON). The Optimization problem is solved using Genetic Algorithms (GAs). In order to remove non-manufacturable shapes, the cluster of materials and cleaning method is used and applied into magnet and air cells, respectively. The minimum number of cells in a cluster (Nmin) is defined as an integer design parameter. The analytical method can significantly reduce the computation time used by optimization process as compared with methods based on Finite Element Analysis (FEA). This method is applied to a 12-pole SPMS machine. Validation of the S-C mapping method and final results are carried out using 2D and 3D finite element analysis. The results obtained demonstrate that asymmetrical magnet shape improves cogging torque and torque ripple performance of SPMS machine by a significant margin.

14 August 2020 in Electrical Engineering
Verified
Journal Article
Closed access
PDF file
SMSeyed Abolfazl Mortazavizadeh
Seyed Abolfazl Mortazavizadeh
MEMohammad Ebrahimi
Mohammad Ebrahimi
AGAhmad Ghaderi
Ahmad Ghaderi
MHMasood Hajian
Masood Hajian

29 August 2013 in Journal of Vibration and Control
Verified
Journal Article
Closed access
AGAmin Gholabi
Amin Gholabi
MEMohammad Ebrahimi
Mohammad Ebrahimi
GYGholam Reza Yousefi
Gholam Reza Yousefi
MGMostafa Ghayour
Mostafa Ghayour
AEAli Ebrahimi
Ali Ebrahimi
HJHamed Jali
Hamed Jali
One of the most critical issues in overhead cranes is the swing of a suspended load while the crane starts to move and accelerates, changes the movement direction, breaks or stops. This can lead to severe damage, and therefore several methods have been applied to damp the load swings. Most of these methods are based on information about the swing angle of a suspended load. In traditional methods, camera vision, acceleration or inclinometers sensors, simple pendulums and other types of sensors have been used. Generally, a method is desired if it can estimate the swing angle with the least equipment costs, while using an uncomplicated calculation method and the minimum sensitivity to environmental situations and industrial noises. In this paper, a new algorithm is proposed to estimate the swing angle. To do so, the supplied voltage and current of the induction motor which drives the trolley are measured, and then using a new proposed method based on a dynamic analysis of the mathematical dynamic model, the swing angle is estimated and is used in the controller system to damp the swings. The proposed method is verified by means of computer simulations.