Saule Sagintayeva

Saule Sagintayeva

Auto-generated profile, based on publicly available information

Saule Sagintayeva

Department of Metallurgy and New Materials, Abylkas Saginov Karaganda Technical University, Karaganda 100000, Kazakhstan

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 March 2026 in Metals
Verified
Journal Article
Open access
PDF file
AIAristotel Issagulov
Aristotel Issagulov
ZSZhalgas Saulebek
Zhalgas Saulebek
SSSagintayeva Saule
Sagintayeva Saule
YMYerbolat Makhambetov
Yerbolat Makhambetov
This study quantitatively evaluates the effect of solid-phase pre-reduction of chromite concentrate on the energy efficiency and techno-economic performance of high-carbon ferrochrome (HC FeCr) smelting. Laboratory pre-reduction experiments were conducted at 1200–1400 °C using Shubarkol coal, metallurgical coke, and special coke as carbonaceous reducing agents. Structural and phase transformations were characterized by X-ray diffraction (XRD) and scanning electron microscopy with energy-dispersive spectroscopy (SEM-EDS). At 1200 °C, the degree of metallization remained low (<5%), whereas at 1400 °C it increased to 41.3% under laboratory conditions and up to 65% in pilot-scale tests due to the decomposition of the spinel matrix and the formation of metallic and carbide phases. The application of pre-reduced feedstock in a submerged arc furnace reduced specific electricity consumption by up to 33.5% compared with conventional smelting and increased chromium recovery to 89.71%. Industrial-scale extrapolation indicates the potential to decrease power consumption to approximately 3190 kWh/t of alloy. Techno-economic analysis demonstrates that the use of pre-reduced feedstock reduces the production cost by approximately 10–23%, depending on the type of carbonaceous reducing agent (Shubarkol coal, metallurgical coke, or special coke). Special coke provided the highest energy efficiency, whereas Shubarkol coal ensured the greatest direct economic benefit. The integrated microstructural, energetic, and economic assessment confirms the industrial applicability of the proposed pre-reduction approach.

4 June 2026 in Metals
Verified
Journal Article
Open access
PDF file
AIAristotel Issagulov
Aristotel Issagulov
AMAibar Myrzagaliyev
Aibar Myrzagaliyev
SSSagintayeva Saule
Sagintayeva Saule
YMYerbolat Makhambetov
Yerbolat Makhambetov
This study evaluated the production of aluminosilicochrome alloy (ASC) from technogenic wastes generated by ferroalloy and coal production. Chromite spinel dust from high-carbon ferrochrome gas cleaning, microsilica from ferrosilicon gas cleaning, and coal sludge as a reductant were used as raw materials. Thermodynamic modeling of the Fe–Cr–Si–Al–C–O system in HSC Chemistry 10 predicted that ASC formation is most favorable at 2000–2200 °C, where the metallic phase should contain (wt. %) 28.27–29.46 Cr, 35.21–36.06 Si, 10.14–11.89 Al, and 10.21–10.45 Fe. These predictions were tested by smelting a pre-agglomerated monocharge in a 100 kVA single-electrode electric arc furnace. The resulting alloy contained (wt. %) 24.23 Fe, 32.03 Si, 22.32 Cr, 18.70 Al, 0.36 C, 0.028 P, and 0.015 S. The experiments confirmed the formation of Si-, Cr-, and Al-rich ASC and demonstrated the feasibility of carbothermic production from these wastes. SEM-EDS revealed a multicomponent metallic matrix with pronounced microstructural heterogeneity and local redistribution of Fe, Si, Cr, and Al. Overall, the results support the use of fine technogenic wastes for producing a complex Fe–Cr–Si–Al alloy.

14 August 2026 in Metals
Verified
Journal Article
Open access
PDF file
AIAristotel Issagulov
Aristotel Issagulov
AMAibar Myrzagaliyev
Aibar Myrzagaliyev
SSSaule Sagintayeva
Saule Sagintayeva
YMYerbolat Makhambetov
Yerbolat Makhambetov
DIDiana Issagulova
Diana Issagulova
KIKuanysh Ilyassov
Kuanysh Ilyassov
This study investigates the possibility of using aluminosilicochrome (ASC) produced from technogenic raw materials as a potential alternative to FSC-48 ferrosilicochrome in refined ferrochrome smelting. Laboratory smelting tests were carried out in an induction furnace using alumina crucibles with a charge mass of 50 g. The two variants were compared based on the material balance, SEM-EDS analysis of the metallic and slag phases, a conditional estimate of chromium transfer to the metal, and the results of thermodynamic modeling in FactSage 8.4. It was established that a Cr–Fe metallic phase is formed when both FSC-48 and ASC are used. The average metal mass was 13.8 g for FSC-48 and 13.3 g for ASC. According to SEM-EDS data, the Cr content in the metallic phase was 70.53 and 68.64 wt. %, respectively. Aluminum introduced with ASC predominantly transfers into the slag, increasing its Al content to 20.81 wt. %. The conditional estimate of total chromium transfer from the charge to the metallic phase was 91.9% for FSC-48 and 91.6% for ASC. FactSage modeling showed higher calculated ore-derived Cr recovery for ASC under equilibrium conditions; however, excessive ASC addition increased the Si content in the metal. The obtained results confirm the fundamental possibility of using ASC as a complex reductant in refined ferrochrome smelting.

21 October 2026 in Metals
Verified
Journal Article
Open access
PDF file
AIAristotel Issagulov
Aristotel Issagulov
AKAnuar Kopabayev
Anuar Kopabayev
SSSaule Sagintayeva
Saule Sagintayeva
DIDiana Issagulova
Diana Issagulova
NNNurzhan Nurgali
Nurzhan Nurgali
AZArmat Zhakan
Armat Zhakan
This study investigates a two-stage duplex process for producing low-carbon ferrochrome based on sequential mixing of molten ore–lime and metallic melts, with emphasis on its adaptation to the raw materials and operating conditions of the Aktobe Ferroalloy Plant. Unlike the conventional process, in which the chromite ore–lime charge directly interacts with ferrosilicochromium, the proposed approach distributes FeSiCr between two successive stages of melt interaction to improve chromium reduction and metal–slag separation. Kempirsai chromite ore, lime, and ferrosilicochromium (FeSiCr 48) were used as raw materials. Thermodynamic analysis using HSC Chemistry 6.0 confirmed the feasibility of the main reduction reactions at 1600–1800 °C. Pilot-industrial trials produced ferrochrome containing 71.42–73.15% Cr and 1.28–1.31% Si, while the final slag contained 1.54–1.58% Cr2O3 and 0.11–0.14% FeO. X-ray diffraction analysis identified merwinite, gehlenite, and spinel-type solid solutions containing chromium. Dicalcium silicate was not detected, consistent with the observed stone-like structure of the cooled slag. Chromium recovery reached approximately 70%, compared with approximately 65% for the conventional process. The results demonstrate the potential of sequential FeSiCr distribution to improve chromium utilization and reduce chromium losses to slag under the specific conditions of ferrochrome production at the Aktobe Ferroalloy Plant.

22 September 2026 in Metals
Verified
Journal Article
Open access
PDF file
AAAinash Akmanova
Ainash Akmanova
AIAristotel Issagulov
Aristotel Issagulov
SSSaule Sagintayeva
Saule Sagintayeva
DADastan Aubakirov
Dastan Aubakirov
DIDiana Issagulova
Diana Issagulova
YMYerbolat Makhambetov
Yerbolat Makhambetov
The present study compares the effects of temperature, holding time, and nominal carbon excess on the pre-reduction of Donskoy chromite pellets with semi-coke. FactSage equilibrium calculations were interpreted alongside three laboratory series with different baselines. At 180 min with activated bentonite and 25% carbon excess, chromium metallization increased from 58.5% at 1350 °C to 87.0% at 1500 °C. At 1400 °C with attapulgite and 10% excess, extending holding time from 195 to 210 min increased chromium metallization from 70.6% to 82.8%, while residual carbon decreased from 4.96 to 4.00 wt.%. At 1500 °C and 180 min with activated bentonite, increasing excess from 15% to 25% increased chromium metallization from 68.9% to 87.0% and residual carbon from 2.30 to 4.74 wt.%. These condition-specific endpoints do not establish factor interactions, an optimum regime, or a kinetic mechanism. Unavailable uncertainty estimates limit quantitative interpretation. Equilibrium predictions and elemental maps do not independently verify the experimental phase sequence. Any industrial benefits, including chromium recovery, energy consumption, and continuous-process performance, require further validation.