This study investigates the agglomeration of chromium-containing dust from ferroalloy production using rigid vacuum extrusion. Direct utilization of fine technogenic materials in submerged arc furnaces is limited due to poor gas permeability, increased dust generation, and unstable smelting conditions. The aim of this work was to compare bentonite and polymer binders in brex production and evaluate their metallurgical applicability. Chromium-containing dust from the gas-cleaning system of the Aktobe Ferroalloy Plant (TNC Kazchrome JSC, ERG) was characterized using chemical analysis and SEM/EDS methods. The material exhibited a heterogeneous structure composed mainly of chromium-containing spinel, silicate, and oxide phases. Pilot-industrial extrusion tests were performed using J.C. Steele & Sons equipment with bentonite (10 wt.%) and polymer binder TD 021.005.BS (2.5 wt.%). The polymer binder provided improved brex geometry and significantly higher mechanical strength, achieving impact strength values up to 89.5% after curing. SEM/EDS analysis of the obtained brexes confirmed the formation of a dense agglomerated structure with uniform distribution of chromium-containing phases. Thermodynamic modeling using FactSage 8.4 showed that brex addition does not significantly affect slag composition, phase equilibria, or metal quality during high-carbon ferrochrome smelting. The results demonstrate the feasibility of polymer binders for efficient recycling of chromium-containing technogenic wastes by rigid vacuum extrusion.
This study investigates the possibility of using aluminosilicochrome (ASC) produced from technogenic raw materials as a potential alternative to FSC-48 ferrosilicochrome in refined ferrochrome smelting. Laboratory smelting tests were carried out in an induction furnace using alumina crucibles with a charge mass of 50 g. The two variants were compared based on the material balance, SEM-EDS analysis of the metallic and slag phases, a conditional estimate of chromium transfer to the metal, and the results of thermodynamic modeling in FactSage 8.4. It was established that a Cr–Fe metallic phase is formed when both FSC-48 and ASC are used. The average metal mass was 13.8 g for FSC-48 and 13.3 g for ASC. According to SEM-EDS data, the Cr content in the metallic phase was 70.53 and 68.64 wt. %, respectively. Aluminum introduced with ASC predominantly transfers into the slag, increasing its Al content to 20.81 wt. %. The conditional estimate of total chromium transfer from the charge to the metallic phase was 91.9% for FSC-48 and 91.6% for ASC. FactSage modeling showed higher calculated ore-derived Cr recovery for ASC under equilibrium conditions; however, excessive ASC addition increased the Si content in the metal. The obtained results confirm the fundamental possibility of using ASC as a complex reductant in refined ferrochrome smelting.
The present study compares the effects of temperature, holding time, and nominal carbon excess on the pre-reduction of Donskoy chromite pellets with semi-coke. FactSage equilibrium calculations were interpreted alongside three laboratory series with different baselines. At 180 min with activated bentonite and 25% carbon excess, chromium metallization increased from 58.5% at 1350 °C to 87.0% at 1500 °C. At 1400 °C with attapulgite and 10% excess, extending holding time from 195 to 210 min increased chromium metallization from 70.6% to 82.8%, while residual carbon decreased from 4.96 to 4.00 wt.%. At 1500 °C and 180 min with activated bentonite, increasing excess from 15% to 25% increased chromium metallization from 68.9% to 87.0% and residual carbon from 2.30 to 4.74 wt.%. These condition-specific endpoints do not establish factor interactions, an optimum regime, or a kinetic mechanism. Unavailable uncertainty estimates limit quantitative interpretation. Equilibrium predictions and elemental maps do not independently verify the experimental phase sequence. Any industrial benefits, including chromium recovery, energy consumption, and continuous-process performance, require further validation.
30 June 2025 in Научный журнал "Вестник Актюбинского регионального университета имени К. Жубанова"
Жоғары сапалы минералдық ресурстардың сарқылу жағдайында нашар және байыту қиын кендерді өңдеудің тиімді технологияларын жасау ерекше өзектілікке ие болуда. Бұл жұмыста Шалқия кен орнының полиметалл кенінен ферросилицийді аз күлді тотықсыздандырғыштарды (арнайы кокс және аз күлді көмір) қолдану арқылы карботермиялық тотықсыздандыру арқылы алу мүмкіндігі қарастырылған. Зерттеу тепе-теңдік құрамы модуліндегі HSC Chemistry (Outokumpu) бағдарламалық пакетіне негізделген термодинамикалық модельдеу әдістерін қолдану арқылы жүргізілді. Fe-Si-Zn-C-O жүйесіндегі тепе-теңдік фазалық қатынастары кең температура диапазонында (500-2100°С) есептеліп, металдық және газ фазалары арасындағы элементтердің таралуына талдау жүргізілді. Кремнийдің ферроқорытпаға ең жоғары экстракциясы (90%-ға дейін) 1700-1900°С температурада, негізінен темір силициді (FeSi) және бос кремний түрінде қол жеткізілетіні анықталды. Бұл ретте мырыштың газ фазасына тиімді кетуі 1600°С жоғары температурада қамтамасыз етіледі. Алынған нәтижелер алдын ала флотациялық байытуды қажет етпей, құрамында кремний тотығы мен ұшпа компоненттері бар кендерді терең өңдеуге арналған пирометаллургиялық тәсілдің әлеуетін растайды. Ұсынылған деректер Шалқия кен орнының рудаларынан құрамында кремнийі бар әртүрлі қорытпаларды алу бойынша тәжірибелік сынақтар жүргізуге негіз бола алады.
30 September 2025 in Science and Technology of Kazakhstan
The object of study was 30KhGS steel melted with briquettes made from fine-dispersed dust (FDD) of ferroalloy production. The samples melted with FS50-7 were used for reference. Experimental briquettes were made from fine-dispersed dust of ferrosilicon production with the addition of iron ore concentrate, and bentonite clay was used as a binder. The chemical composition, mechanical properties, and microstructure of 30KhGS steel melted with the briquettes were studied. Mechanical tests, hardness measurements, and microstructural analysis were carried out to evaluate the performance of the steel produced. The results showed that during deoxidation with the experimental briquettes, the chemical composition and mechanical properties of steel corresponded to GOST standards for this grade. The use of such briquettes led to improved resource efficiency, reduced production costs, and minimized environmental footprint. Moreover, the briquetted product obtained via this technique can be further utilized in industrial-scale metallurgical operations. The findings suggest a promising approach for sustainable steel production through waste recycling in the ferroalloy industry. Keywords: steel, bentonite clay, Off-grade fine ferrosilicon (FFS), iron ore concentrate, fine-dispersed dust (FDD), deoxidation.
30 December 2025 in Science and Technology of Kazakhstan
В статье исследуется влияние редкоземельных металлов (РЗМ), таких как церий (Ce), неодим (Nd) и диспрозий (Dy), на механические свойства стали 09Г2С, используя данные существующих научных исследований. Основное внимание уделено влиянию неметаллических включений (оксидов и сульфидов) на прочностные и износостойкие характеристики стали, 09Г2С, широко используемой в строительстве ответственных конструкций, таких как каркас локомотивов. а также возможности их оптимизации через добавление РЗМ. Рассмотрены ключевые улучшения, такие как повышение прочности, термостойкости, износостойкости и коррозионной стойкости, при добавлении этих металлов в сталь. Обоснование этих эффектов основано на уже опубликованных результатах исследований, демонстрирующих, как редкоземельные элементы способствуют улучшению эксплуатационных характеристик материалов. В статье также акцентируется внимание на значении местных ресурсов РЗМ Казахстана для снижения стоимости легирования стали и зависимости от импорта. Особое внимание уделено церийному легированию стали, поскольку оно предлагает значительные улучшения при более доступной стоимости по сравнению с неодимом и диспрозием. Полученные выводы могут быть использованы при разработке новых легированных сталей с заданными эксплуатационными свойствами. Ключевые слова: редкоземельные металлы, механические свойства, сталь 09Г2С, прочность, термостойкость, износостойкость, коррозионная стойкость.