Zulfiya Aubakirova

Zulfiya Aubakirova

Auto-generated profile, based on publicly available information

Zulfiya Aubakirova

Abylkas Saginov Karaganda Technical University, Department of Construction Materials and Technologies, Karaganda, Kazakhstan

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 September 2022 in Technobius
Verified
Journal Article
Open access
PDF file
ZAZulfiya Aubakirova
Zulfiya Aubakirova
AТAldiyar Теmirbekov
Aldiyar Теmirbekov
MKMonika Kulisz
Monika Kulisz
GZGulnaz Zhairbaeva
Gulnaz Zhairbaeva
Statistics of recent years shows an annual increase in the volume of technogenic waste (in particular "tailings") of mining and metallurgical enterprises of Kazakhstan by about 1.5 billion tons, which at the current time is already about 4.7 billion that entails certain environmental and economic consequences. This article proposes the potential use of the tailings of the enterprises as a fine aggregate to partially replace the consumption of cement in the concrete mixture for the manufacture of paving slabs. Carbonate tailings of Kazzinc LLP enterprise were used. To determine the optimum composition of concrete mix with the use of tailings were made control and 4 experimental compositions with the replacement of part of the cement waste in the amount of 5, 10, 15, 20% respectively. Samples of concrete mixtures were tested for compressive strength, flexural tensile strength, abrasion, frost resistance, and resistance to wetting and drying. According to the test results, it was found that as the concentration of tailings increases, the physical-mechanical and operational indicators of the concrete mixture and concrete for the manufacture of paving slabs improve.

2 March 2025 in Technobius
Verified
Journal Article
Open access
PDF file
DADarya Anop
Darya Anop
OROlga Rudenko
Olga Rudenko
VSVladimir Shevlyakov
Vladimir Shevlyakov
ZAZulfiya Aubakirova
Zulfiya Aubakirova
NSNikolai Soshnikov
Nikolai Soshnikov
MBMeiram Begentayev
Meiram Begentayev
The article presents the results of studies on forecasting the compressive strength and density of aerated ash concrete. A theoretical review was conducted on the variability of strength and density of cellular concretes when selecting their compositions. A series of experiments was conducted to study the dynamics of changes in the compressive strength and density of non-autoclaved gas-ash concrete during the initial stages of hardening under natural conditions and after thermal treatment to select a composition of the specified quality. It was revealed that it is possible to control both the strength and the density at the early stages of hardening to forecast these parameters at the design age of 28 days. It was established that the compressive strength of aerated ash concrete samples hardening under natural conditions increased by an average of 42.62% at the design age compared to the strength at 7 days, while the density decreased on average by 19.19%. For aerated ash concrete samples that underwent thermal treatment (steaming), the increase in strength averaged 34.67%, and the decrease in density was 11.07%. The obtained results are of practical value for scientists and engineers engaged in the development of cellular concrete compositions.

24 November 2024 in Technobius
Verified
Journal Article
Open access
PDF file
ZAZulfiya Aubakirova
Zulfiya Aubakirova
MRMurat Amanzholovich Rakhimov
Murat Amanzholovich Rakhimov
GRGaliya Rakhimova
Galiya Rakhimova
MKMonika Kulisz
Monika Kulisz
Tymarkul MuzdybayevaTymarkul Muzdybayeva
Tymarkul Muzdybayeva
Developing a fine-grained concrete composition for additive technologies is an important scientific and practical task, since traditional building mixtures are unsuitable for 3D printers, and special solutions are practically absent in mass production. This study aims to develop a composition of fine-grained concrete for additive technologies using local resources and ash and slag waste of the Ust-Kamenogorsk thermal power plant, which contributes to the expansion of the raw material base used in this area. The work was carried out taking into account the analysis of the literature review, which made it possible to identify key aspects and directions in the development of concrete mixtures for additive technologies. This article discusses the possibility of using ash and slag waste in concrete as a filler. Ash has a grain size comparable to river sand, so it can be used as a new material to replace fine filler. To obtain the mixture, 5 experimental mixtures and one reference sample were prepared. The optimal composition is considered to include 30% of M500 Portland cement, 40% of sand, and 30% of ash and slag. The physical and mechanical characteristics of this composition are as follows: the mobility of the mixture is 5.81 cm, and the setting completion time is 4 hours 19 minutes. The results of the sample tests confirmed that the created fine-grained concrete compositions are suitable for extrusion on construction 3D printers. The possibility of creating a composition based on local ash and slag waste for additive technologies used in producing small architectural forms was experimentally confirmed.

30 June 2025 in Nanotechnologies in Construction: A Scientific Internet-Journal
Verified
Journal Article
Closed access
MRMurat Amanzholovich Rakhimov
Murat Amanzholovich Rakhimov
IMI. Menéndez-Pidal
I. Menéndez-Pidal
ZAZ.A. Aubakirova
Z.A. Aubakirova
AAAliya K. Aldungarova
Aliya K. Aldungarova
ZMZhangazy Moldamuratov
Zhangazy Moldamuratov

29 March 2023 in Technobius
Verified
Journal Article
Open access
PDF file
GZGulnaz Zhairvaeva
Gulnaz Zhairvaeva
ZAZulfiya Aubakirova
Zulfiya Aubakirova
YIYana Ivashina
Yana Ivashina
ASAlexandr Soldun
Alexandr Soldun
AMAlina Makienko
Alina Makienko
This paper examines the potential of 3D printing for additive manufacturing of street furniture, specifically a flowerbed measuring 1.63 m in length, 0.3 m in height according to a custom design. The study investigates the production process, material selection, and design considerations for street furniture, as well as the workability of the selected concrete mixture and the strength of the hardened structure. It uses the S-6045 3D printer to produce the flowerbed and tests the concrete mixtures for workability and strength of concrete at the age of 28 days. The study produced a concrete mixture that exhibits the required attributes for use with the S-6045 3D printer. The findings may also have implications for other applications of additive manufacturing in the urban environment.