The world's first single-chip RF transceiver to support 5G sub-6-GHz new radio (NR) and long-term evolution (LTE) E-UTRA New Radio-Dual Connectivity (EN-DC) in 14-nm FinFET CMOS technology is presented. The single-chip transceiver integrates identical primary and diversity receivers (RXs) with seven pipelines for supporting four inter-band carrier aggregation (CA) with three 4 x 4 MIMO, two independent transmitter (TX) chains, eight frequency synthesizers for RX and TX, and on-chip digitally controlled crystal oscillator (DCXO) to reduce the phase noise and bill of material (BOM) cost. The receiver features 12 single-ended low-noise amplifiers (LNAs) with wideband characteristics. With the help of the proposed pipeline structure and frequency-band switchable transformer, the die size can be reduced despite covering the whole frequency range from 2G to sub-6-GHz 5G NR. It achieves the noise figure (NF) from 6.5 to 9.3 dB, +3-dBm out-of-band (OOB) IIP3, more than +70-dBm OOB IIP2 after calibration. For the transmitter, low RX-band noise and harmonic suppression technique are applied to support surface acoustic wave (SAW)-less architecture, and the bandwidth control of the baseband filter is implemented for the digital pre-distortion (DPD) operation of 100-MHz BW in NR transmit data. The measured error vector magnitudes (EVMs) in 4G and 5G bands of n79 are -39.5 dB at +4-dBm output power and -33.9 dB at +3.06-dBm output power, respectively, and the measured RX-band noise of 2G is -163 dBc at 20-MHz offset. The RX consumes 18 mW at LTE 1-CA mode and the TX consumes 350 mW at n79.
18 August 2020 in IEEE Journal of Solid-State Circuits
This article presents a fully integrated stand-alone narrowband Internet-of-Things (NB-IoT) and global navigation satellite system (GNSS) system-on-chip (SoC). It aims for an all-in-one system to integrate all necessary blocks such as an RF transceiver, a power management system (PMIP), and a clock management system and to save a bills-of-material (BOM) cost. An RF transceiver is integrated to support multi-band cellular IoT and GNSS with a CMOS RF power amplifier transmitting 23-dBm output power. A PMIP, including bucks, a boost, and low-dropout regulators (LDOs), is integrated to support coin cell or AAA battery and to support a wide input supply voltage range from 2.5 to 5 V. In addition, clock management system is embedded with a digitally controlled crystal oscillator (DCXO), a relaxation oscillator (RCO), and temperature sensor units (TSUs). It is fabricated in a standard 28-nm CMOS process and its size is 24.6 mm². The power consumption of always-on-block is 15 μW, and the sleep current consumption is less than 10 μA at 3.8 V.
11 October 2023 in IEEE Journal of Solid-State Circuits
This article presents a 16-Gb/s/pin 0.764-pJ/b single-ended four-level pulse-amplitude modulation (PAM-4) transceiver in a 4-nm CMOS process. A switching-jitter compensation technique is proposed in the receiver (RX) to improve timing margins from 0.31 to 0.37 UI at 16 Gb/s, as it adjusts transition slope of the front-end outputs. To compensate for signal-to-noise ratio (SNR) degradation in a PAM-4 signal, relaxed impedance matching is used, where 20 $\Omega$ is used as a transmitter (TX) impedance instead of 50 $\Omega$ . To maximize eye openings further, fractionally spaced feedforward equalization (FS-FFE) is used with a tap spacing of 0.8 UI. The relaxed termination scheme along with FS-FFE improves eye openings by 2.25 times compared with the conventional design using a 50- $\Omega$ TX impedance with 1-UI spacing FFE.
9 October 2024 in IEEE Journal of Solid-State Circuits
In this article, we introduce a new dynamically biased ring amplifier that is tolerant to mismatch and PVT variation without requiring bias calibration, and we verify it in a 12-bit 400-MS/s pipelined-SAR analog-to-digital converter (ADC), fabricated in an 8-nm FinFET process. Our novel ring amplifier solves the biasing issues inherent in conventional ring amplifiers while maintaining the benefits of high gain, slew-based charging, and nearly rail-to-rail output swing. We also propose a technique to enhance the DC accuracy of a switched-capacitor common-mode feedback (CMFB) without consuming additional power, which we named feedback voltage sampling CMFB. Furthermore, we introduce a full-scale matching residue amplification technique for the prototype pipelined-SAR ADC to utilize the top-plate input sampling for the first-stage SAR ADC, resulting in faster and lower power conversion. The prototype ADC demonstrates the robustness of our dynamically biased ring amplifier to mismatch and PVT variation without any interstage gain, bias, or reference calibration, and achieves 64.4-dB SNDR and 77.6-dB SFDR for a low-frequency input while consuming 2.08 mW. This measured performance is equivalent to Walden and Schreier FoMs of 3.8 fJ/conversion $\cdot$ step and 174.2 dB, respectively.
We provide an alternative analytic approximation for the value of an American option using a confined exponential distribution with tight upper bounds. This is an extension of the Geske and Johnson compound option approach and the Ho et al. exponential extrapolation method. Use of a perpetual American put value, and then a European put with high input volatility is suggested in order to provide a tighter upper bound for an American put price than simply the exercise price. Numerical results show that the new method not only overcomes the deficiencies in existing two-point extrapolation methods for long-term options but also further improves pricing accuracy for short-term options, which may substitute adequately for numerical solutions. As an extension, an analytic approximation is presented for a two-factor American call option.
29 October 2020 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Adaptive 5G architecture consisting of three functional sections (four antenna components, tunable matching network (TMN), and radio frequency (RF) front-end package) is proposed, analyzed and verified. In the 5G mmWave spectrum, the RF performance is highly dependent on the specific antenna package technology. However, compact antenna packages oftentimes result in undesired interference between the antenna elements. This eventually leads to severe RF performance degradation. For the first time in literature, a mmWave 5G RFIC and the TMN are integrated for efficient operation that is applicable to real-life 5G mobile devices. Moreover, the proposed antenna-in-package (AiP) architecture enables independent frequency control at multiple frequencies. The proposed solution is simulated and measured at the system level. As a result, the devised AiP solution exhibits a simulated effective isotropic radiated power (EIRP) of 22.05–23.96 dBm at the cumulative distribution function (CDF) of 50% by applying the conducted power of 17 dBm (per channel), and the peak gain of the antenna exhibits 13.7 dBi at 27 GHz (state A) and 12.6 dBi at 28 GHz (state B) with an amplifier having an output power of 5 dBm.