Srinivas Gulur

Srinivas Gulur

Auto-generated profile, based on publicly available information

Srinivas Gulur

ECE, North Carolina State University, Raleigh, North Carolina United States 27606

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 October 2019 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Open access
VIVishnu Mahadeva Iyer
Vishnu Mahadeva Iyer
SGSrinivas Gulur
Srinivas Gulur
GGGhanshyamsinh Gohil
Ghanshyamsinh Gohil
SBSubhashish Bhattacharya
Subhashish Bhattacharya

19 September 2018 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
VIVishnu Mahadeva Iyer
Vishnu Mahadeva Iyer
SGSrinivas Gulur
Srinivas Gulur
SBSubhashish Bhattacharya
Subhashish Bhattacharya
A two stage electric vehicle (EV) battery charger typically consists of an $\mathcal {ac - dc}$ converter cascaded with a $\mathcal {dc - dc}$ converter. In such a cascaded system, maintaining stability at the intermediate $\mathcal {dc}$ link is imperative for reliable operation of the battery charger under different operating modes. This paper addresses the intermediate $\mathcal {dc}$ link stability challenges that exist in a bidirectional two-stage grid connected singlephase battery charger. It is delineated that the small-signal load dependent resistance of the $\mathcal {ac - dc}$ converter plays a crucial role in determining the stability of the bidirectional battery charger. A virtual-resistor-based active damping control strategy that does not require any additional sensors is explored for the $\mathcal {ac - dc}$ converter to stabilize the cascaded system under all operating modes irrespective of the power flow direction. Experimental results on a grid connected single-phase battery charger hardware prototype are presented to validate the proposed models and showcase the improvement in $\mathcal {dc}$ link stability due to the virtual-resistance-based active damping approach.

9 January 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
SGSrinivas Gulur
Srinivas Gulur
VIVishnu Mahadeva Iyer
Vishnu Mahadeva Iyer
SBSubhashish Bhattacharya
Subhashish Bhattacharya
Increase in renewable energy penetration, in the recent past, has been the primary cause for grave issues in power quality in the utility grid. This has ushered in the need for a robust and stable control system for reference tracking and disturbance rejection of grid connected converters. Conventionally, due to its simplicity and ability to achieve zero steady state error, a simple proportional integral (PI) controller is used in the synchronous reference frame (dq) for current control of voltage source based grid connected systems. However, the PI controller by itself, may not suffice for adequate disturbance rejection, especially when the utility grid voltages contain other harmonics in addition to the fundamental component. This paper introduces and analyzes a dual loop current control structure which utilizes two independent controllers, one for reference tracking and the other for disturbance rejection in the dq frame. A small signal model of the dual loop current control has been presented and its robustness under grid impedance variation, examined. Extensive experimental results are presented to validate the dual loop control strategy for improved disturbance rejection capability and filtering action during the presence of grid voltage disturbances and grid impedance variations, without compromising on the reference tracking performance.

5 November 2019 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Open access
SGSrinivas Gulur
Srinivas Gulur
VIVishnu Mahadeva Iyer
Vishnu Mahadeva Iyer
SBSubhashish Bhattacharya
Subhashish Bhattacharya
Common mode (CM) filters play a crucial role in determining adherence to conduced emissions (CE) standards for grid-tied voltage source converters. Design and implementation of such filters can be challenging since they depend on several factors like identification of CM noise paths, fidelity of passive components and discerning the frequency and amplitude of CM noise sources. In this work, a common mode (CM) filter has been proposed which uses passive components along with the converter's heat-sink as a circulating return path for the CM currents. Based on the presented CM circuit models with the proposed filter, a detailed design process has been delineated for selecting the passive components required to realize the CM filter. Additionally, the heat-sink potential has been shown to be touch safe during both ideal and non-ideal grid conditions with the proposed CM filter. CE spectral results measured using a commercially procured Line Impedance Stabilization Network (LISN) and captured time domain converter operational wave-forms for a 2-level, 3 phase grid-tied voltage source converter (VSC) validate the functionality and effectiveness of the presented design.

16 June 2021 in IEEE Access
Verified
Journal Article
Open access
VIVishnu Mahadeva Iyer
Vishnu Mahadeva Iyer
SGSrinivas Gulur
Srinivas Gulur
SBSubhashish Bhattacharya
Subhashish Bhattacharya
JKJun Kikuchi
Jun Kikuchi
SSSrikanthan Sridharan
Srikanthan Sridharan
CCChingchi Chen
Chingchi Chen
This paper analyzes the low-frequency stability challenges that exist in a complex DC microgrid (MG) system. The converters that belong to a DC MG are categorized into different groups based on their control approach. The small-signal model of the DC MG is presented, and the conditions for system stability are derived. In some DC MG applications, there is the possibility of installing off-the-shelf converters with little flexibility and access for controller auto-tuning. To tackle this, a hardware-based active voltage stabilizer solution is proposed to stabilize the DC MG. The active stabilizer’s functionality, based on an isolated bidirectional DC-DC converter, is elucidated, and a suitable control strategy is proposed. The active stabilizer and its associated control configuration involve only local voltage sensing and are non-intrusive. A dual active bridge (DAB) converter-based active stabilizer is implemented, and hardware-based steady-state and transient experimental results from a DC MG test-bench are provided to validate the functionality and effectiveness of the proposed active stabilizer.

20 April 2023 in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
Verified
Journal Article
Closed access
SGSrinivas Gulur
Srinivas Gulur
VIVishnu Mahadeva Iyer
Vishnu Mahadeva Iyer
SBSubhashish Bhattacharya
Subhashish Bhattacharya
This work proposes a common mode (CM) filter configuration for a grid-tied two-stage AC/DC solid state transformer (SST). The proposed CM filter utilizes passive components along with the heat-sinks of the individual power converter stages to mitigate the overall conducted emissions (CE) injected by the SST system into the grid. The working principle of the proposed CM filter is analyzed and elucidated using CM equivalent circuit models. In addition to CE reduction with the proposed CM filter, it is also demonstrated that the heat-sinks of the SST system can be closer to ground-potential while being impedance grounded. The effectiveness of the proposed CM filter is validated by experimentally measuring the CE of the grid-tied SST system using a Line Impedance Stabilization Network (LISN).