Full-chip electrostatic discharge (ESD) protection circuit design verification is needed for complex ICs at advanced technology nodes, which however is still largely impractical due to the limitation of ESD device models and CAD tools. This paper reports a new circuit-level ESD protection design simulation and dynamic checking method using SPICE and ESD device behavior models, which allows comprehensive, quantitative and dynamic verification of ESD protection circuit designs at chip level based entirely on ESD discharging functions. The new ESD protection circuit simulation method is validated using ICs designed and fabricated in a 28nm CMOS. This ESD-function-based ESD circuit simulation method is technology independent, which can handle various ICs including complex multiple power domain circuits and ICs using non-traditional ESD protection structures.
16 October 2018 in IEEE Microwave and Wireless Components Letters
Flying crosstalk through the back-end-of-the-line (BEOL) above the silicon substrate is an emerging design challenge to RF ICs, which cannot be addressed by conventional in-Si noise reduction structures. This letter reports a new concept of using in-BEOL metal wall structures, implemented by 3-D heterogeneous integration, to efficiently suppress the above-Si flying global crosstalk. It was validated using a set of single-pole-double-throw transmitter/receiver (T/Rx) antenna switches fabricated in a foundry 45-nm silicon-on-insulator CMOS process. Measurement shows significant interswitch crosstalk reduction of ~ 18.5 dB or ~ 98.6% suppression clearly.
Transient voltage peaking under very fast electrostatic discharge (ESD), like charged device model (CDM) pulse, is a serious problem to integrated circuits (ICs). A combined TCAD simulation and very fast transmission line pulse (VFTLP) testing method is proposed to thoroughly investigate the transient voltage peaking phenomena of diode-based ESD protection structures under CDM stressing. The study of a set of diode, diode-string and diode-triggered silicon-controlled rectifier (DTSCR) ESD protection structures, fabricated in a 28nm CMOS process, reveals that the inductive impedance along the ESD discharging path may be the root cause of voltage peaking under CDM stressing. The observation provides the design insights overcoming the voltage peaking problem in ESD protection designs before complicate CDM package level testing.
8 September 2020 in IEEE Journal of the Electron Devices Society
This paper reports design, fabrication and analysis of a novel under-transistor (under-FET) in-hole thermal sensor diode structure. Being able to accurately monitor self-heating of individual transistor in-operando, the under-FET temperature sensor enables smart full-chip run-time thermal management with spatial resolution down to single transistor level. The in-hole thermal sensors were fabricated in a CMOS process and validated in measurements. The new chip level thermal management technique was demonstrated using a prototype power amplifier (PA) IC designed in a foundry 40nm CMOS. It opens a door for self-learning based full-chip real-time intelligent thermal management for future ICs.
This paper reports a study of transient behaviors of diode-triggered silicon-controlled rectifier (DTSCR) electrostatic discharging (ESD) protection structures for ultra-fast Charged Device Model (CDM) ESD protection. The DTSCR ESD protection structures, fabricated in a 28nm CMOS process, were characterized using a new combined Very Fast Transmission Line Pulse (VFTLP) testing and TCAD simulation approach, which resolves the deficiency problem of VFTLP testing due to the effects of ultra-short duration of CDM ESD pulse waveforms. The result reveals critical difference of DTSCR behaviors under VFTLP and real CDM ESD that gives a better evaluation of overshooting, turn-on time, turn-on delay, etc.
Compact and robust electrostatic discharging (ESD) protection structures are critical to on-chip ESD protection for ICs. Conventional in-Si ESD protection structures have many disadvantages. A new above-IC graphene NEMS (gNEMS) switch is reported as an ESD protection structure, which features almost zero leakage and robust ESD protection. A systematic characterization of gNEMS ESD structures was conducted by transient transmission line pulse (TLP) testing. The statistical analysis reveals the relationship between ESD discharging behaviors and the influences of gNEMS device dimensions and TLP testing conditions on ESD discharging.