11 July 2024 in Journal of the Mechanical Behavior of Biomedical Materials
Ceramic lattices hold great potential for bone scaffolds to facilitate bone regeneration and integration of native tissue with medical implants. While there have been several studies on additive manufacturing of ceramics and their osseointegrative and osteoconductive properties, there is a lack of a comprehensive examination of their mechanical behavior. Therefore, the aim of this study was to assess the mechanical properties of different additively manufactured ceramic lattice structures under different loading conditions and their overall ability to mimic bone tissue properties. Eleven different lattice structures were designed and manufactured with a porosity of 80% using two materials, hydroxyapatite (HAp) and zirconium dioxide (ZrO2). Six cell-based lattices with cubic and hexagonal base, as well as five Voronoi-based lattices were considered in this study. The samples were manufactured using lithography-based ceramic additive manufacturing and post-processed thermally prior to mechanical testing. Cell-based lattices with cubic and hexagonal base, as well as Voronoi-based lattices were considered in this study. The lattices were tested under four loading conditions: compression, four-point bending, shear and tension. The manufacturing process of the different ceramics leads to different deviations of the lattice geometry, hence, the elastic properties of one structure cannot be directly inferred from one material to another. ZrO2 lattices prove to be stiffer than HAp lattices of the same designed structure. The Young's modulus for compression of ZrO2 lattices ranges from 2 to 30GPa depending on the used lattice design and for HAp 200MPa to 3.8GPa. The expected stability, the load where 63.2% of the samples are expected to be destroyed, of the lattices ranges from 81 to 553MPa and for HAp 6 to 42MPa. For the first time, a comprehensive overview of the mechanical properties of various additively manufactured ceramic lattice structures is provided. This is intended to serve as a reference for designers who would like to expand the design capabilities of ceramic implants that will lead to an advancement in their performance and ability to mimic human bone tissue.
30 July 2024 in Dental Materials
Objective: To design a patient-specific subperiosteal implant for a severely atrophic maxillary ridge using yttriastabilized additively manufactured zirconia (3YSZ) and evaluate its material properties by applying topology optimization (TO) to replace bulk material with a lattice structure. Materials: A contrast-based segmented skull model from anonymized computed tomography data of a patient was used for the initial anatomical design of the implant for the atrophic maxillary ridge. The implant underwent finite element analysis (FEA) and TO under different occlusal load-bearing conditions. The resulting implant designs, in bulk material and lattice, were evaluated via in-silico tensile tests and 3D printed. Results: The workflow produced two patient-specific subperiosteal designs: a) an anatomically precise bulk implant, b) a TO lattice implant. In-silico tensile tests revealed that the Young's modulus of yttria-stabilized zirconia is 205 GPa for the bulk material and 83.3 GPa for the lattice. Maximum principal stresses in the implant were 61.14 MPa in bulk material and 278.63 MPa in lattice, both tolerable, indicating the redesigned implant can withstand occlusal forces of 125-250 N per abutment. Furthermore, TO achieved a 13.10 % mass reduction and 208.71 % increased surface area, suggesting improved osteointegration potential. Significance: The study demonstrates the planning and optimization of ceramic implant topology. A further iteration of the implant was successfully implanted in a patient-named use case, employing the same fabrication process and parameters.
9 October 2023 in Frontiers in Materials
In the field of stereolithography 3D printing, the portfolio of commercially available photopolymers has burgeoned. Each material family possesses its individual properties. However, corresponding products with specific requirements remain a major challenge. This gap could be filled by combining existing materials. This study aimed to predict Young’s modulus of the specimen manufactured by combining multiple materials using digital light processing (DLP), a subtype of stereolithography. It also aimed to investigate the effects of the printing process on the geometry and mechanical properties of such 3D-printed multimaterials. Using a DLP 3D printer, samples were produced from commercially available pure and mixed materials, and half of the samples underwent post-printing curing. Three-point bending tests were performed to determine the elastic modulus of the samples. The elastic properties have been compared to linear interpolation using the properties of the primary materials. The measurements showed that Young’s modulus ranged from 1.6 GPa to 2.2 GPa for the post-cured materials, with the mixed materials fitting well with the linear interpolation approach. For eight out of nine sample sets, the prediction was within the range of the measurements. In the case of as-printed samples, the elasticity of the primary materials ranged from 0.4 GPa to 0.9 GPa, but all of the mixed materials showed a stiffer behavior than the linear interpolation prediction, up to 57% above the prediction. The dimensions of the printed specimen were measured, and groups of different geometrical deviations were identified. These were analyzed with regard to the printer system and material mixture. In conclusion, this study shows and discusses the effects of the printing process on mechanical and dimensional properties of specimens fabricated using a stereolithographic 3D printer from multiple commercially available primary materials. It discusses a process for predicting the elastic properties of these multimaterials and selecting the mixing ratios to achieve specifically desired properties.
26 July 2024 in Open Ceramics
1 April 2026 in BMC Oral Health
Realistic soft-tissue behaviour is essential for surgical training, yet most additively manufactured models remain mechanically homogeneous. The purpose of