16 February 2022 in IEEE Transactions on Power Electronics
A controller for output voltage and power regulation is important for the wireless charging system. For the controller design, it is crucial to establish the accurate system model with considering the time delay, as high time delay exists due to wireless communication, data sampling, and processor calculations for a practical wireless power transfer system. Presently, the common modeling methods, such as the coupled-mode method are based on circuit theories and the component parameters. However, the exact parameters are hard to get due to the diversity of the equipment and application scenarios. Especially, the circuit theories modeling cannot deal with the time delay from hardware limitation and wireless communication. Alternatively, a data-driven modeling method based on the simplified refined instrumental variable method is proposed in this article to get the control-oriented model with time delay. Moreover, based on the estimated model, a controller based on the internal model control is designed to regulate the output voltage. It is shown that the models obtained based on different sampling times are able to accurately describe the system dynamics and the controllers designed based on them are able to achieve the desired control performance.
16 March 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper develops a method of input design for the identification of wireless power transfer (WPT) systems based on receding horizon D-optimization. The dynamic behavior of the system is characterized by a discrete-time, Single-Input, Single-Output (SISO) model, and the associated model parameters are estimated by a recursive least-squares method. To improve the quality of the parameter estimates, the excitation signal of the system is designed based on receding horizon D-optimization. To improve the convergence and efficiency of the input design process, the Sequential Quadratic Programming (SQP) method is employed to solve the receding horizon D-optimization. Numerical and experimental results are presented to demonstrate the effectiveness of the proposed method.
14 December 2023 in IEEE Transactions on Power Electronics
In the field of control-oriented modeling of wireless power transfer (WPT) system, it is urgent to establish a simple model to reflect the nonlinear characteristics introduced by phase-shift control methods, which is significant to the design of controllers. Due to the nonlinear nature introduced by phase-shift control, controllers designed based on specific steady-state small-signal models struggle to maintain closed-loop dynamic performance. In this article, the nonlinearities of the WPT system are implicitly considered by using the Hammerstein model-based identification (HMI) method, so the accuracy of the identified model is guaranteed even if the working point changes, which is unique advantage compared with other methods. In particular, an uncertainty model is precisely established via a frequency-domain analysis approach to introduce the nonlinear characteristics and the statistical properties of identification into the H $\infty$ control problem, which maintains the robustness of closed-loop WPT system. Finally, an experiment is given to verify the effectiveness of HMI method and proposed H $\infty$ robust controller.
18 January 2021 in IEEE Transactions on Power Electronics
A high-power inductive power transfer system with overlapped transmitters driven by a multi-inverter topology is proposed in this article. Each inverter drives an independent primary coil to transfer energy to the common secondary coil. A phase-shifted control strategy at inverter-level is proposed to regulate the output of the system. A dynamic model based on virtual resonant loop is proposed to describe the system with the phase-shift angle and the output voltage as the input and output variables, respectively. With the introduction of virtual resonant loop, n practical resonant loops at the primary side can be expressed by two equations, which greatly reduce the scale and order of the model. A PI controller is developed to evaluate the system regulating performance. A laboratory prototype driven by three inverters connected in parallel was built to verify the theoretical analysis. Experiments have shown that the setting times were within 13 ms under load resistance and reference disturbances, which verified the validity of the model and the controller.
1 January 2025 in IEEE Transactions on Industrial Electronics
30 January 2025 in IEEE Transactions on Power Electronics
Large-strand-count Litz wire (LLW) coils are commonly utilized in high-power wireless power transfer systems. An accurate ac-resistance prediction method of LLW coil is necessary to select the proper operation frequency dedicated for the highest coil quality factor and system efficiency. However, most present literatures ignore the interstrands nonuniform current distribution (NCD) of LLW caused by the soldering tins at terminals, which leads to a high ac-resistance prediction error. This article develops a method extracting the NCD among strands based on the two-dimension finite element analysis and strands probability transposition. And an improved ac-resistance prediction method considering the NCD is proposed subsequently, which is primarily applicable to LLW containing over 500 strands. Moreover, a novel strand edge-soldering connector (SEC) is designed to mitigate NCD and thereby reducing ac-resistance. Finally, the satisfactory accuracy of improved ac-resistance prediction for LLW circular coils up to 1000 strands is verified experimentally. Then, the proposed SEC prototype is measured with a maximum resistance reduction of 33.28%, which demonstrates the effectiveness of the proposed NCD mitigation method.