1 July 2012 in Key Engineering Materials
Condition monitoring and fault detection systems are becoming increasingly important in rail vehicles maintenance and operation, ensuring safety and reliability improvement. Light rail systems are not the main target for this trend, because of low operational speed and lower safety factors. Nevertheless public transport operators begin to pay a closer attention to the technical state monitoring of vehicle and track, in order to reduce maintenance cost and increase safety and ride comfort for passengers, which is an important challenge for public transport competitiveness in XXI century. The paper describes the main concept of the innovative on-board condition monitoring system for light rail vehicle and track. Functional requirements, assumptions and procedures are described, as well as the on-board data acquisition unit with necessary transducers, which number, function and technical parameters were optimized during the research phase of the project. The prototype of the presented system is now being tested in normal operating conditions.
11 February 2021 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
The article discusses the influence of out-of-roundness (OOR) type of wheel shape deviations on its interaction with the rail. The analysis was carried out using multibody simulation technique (MBS). Measurements of tram wheel rims and sample models of flat spots were used as input data. It has been observed that the presence of wheel OOR deviations caused a significant increase in vertical impact loads at the interface between the wheel and the rail, which favours rolling contact fatigue formation. Deviations created at the stage of manufacturing the wheel rim (usually while the profile of the rim itself is turned on a lathe) were amplified by increasing amplitudes and were also visible during the measurement of worn rims, thus creating inequalities with dominant amplitudes. Flat spots present on the rolling surfaces of the wheels cause cyclic jumps of vertical force at the contact point of the wheel and the rail, with maximum values depending on the depth and radius of the rounded edges of the flat spot, and thus subject to change in subsequent stages of the flat spot development. Taking into account the observations made, preventive measures have been proposed against the development of OOR deviations in tram wheels, the origin of which is primarily in the machining process.
6 August 2019 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
This paper presents the concept of a simple system for the identification of the technical condition of tracks based on a trained learning system in the form of three independent neural networks. The studies conducted showed that basic measurements based on the root mean square of vibration acceleration allow for monitoring the track condition provided that the rail type has been included in the information system. Also, it is necessary to select data based on the threshold value of the vehicle velocity. In higher velocity ranges (above 40 km/h), it is possible to distinguish technical conditions with a permissible error of 5%. Such selection also enables to ignore the impact of rides through switches and crossings. Technical condition monitoring is also possible at lower ride velocities; however, this comes at the cost of reduced accuracy of the analysis.
6 November 2019 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
In tram operations, flange wear is predominant due to the low-radius curves and inappropriate technical conditions of the infrastructure; hence, investigations should be focused on the interaction between the wheel flange and the rail gauge corner. Moreover, the calculation methods based on the Hertzian model (elliptic contact patch) provide less accurate results due to the contact occurrence in the wheel flange region. This paper presents a methodology of a finite element method to predict the tram wheel wear in complex motions. The new procedure is based on the Abaqus software and several other sub-procedures written in Python and Fortran. Multibody simulations were used to determine the wheel–rail alignment. In this method, accuracy was chosen at the expense of the computational effort. The main steps are: preparation of models and ride scenarios, multibody simulation for calculating the wheel–rail alignment for different track scenarios and multiple runs of finite element method analysis to determine the wear magnitude. The proposed methodology presents a good agreement with the measurements and can be considered as guidelines for a proper configuration of the flange-designing experimental setup where the influence of the technical conditions of the infrastructure should be introduced adequately.
2 February 2023 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
The paper presents the use of a new method of imaging of the wheel-rail interface wear adopting thermal imaging techniques. Based on the heat generated at the point of contact, coming from the friction and strain of the mating materials, it is possible to identify the type and location of the wheel-rail interface. This work presents the usability of the method with reference to the typical conditions of operation of light rail vehicles (small-radius curves – from 22 m, wheel diameter around 0.6 m, lower standard of track maintenance than in the case of regular railways, use of shallow-grooved frogs, etc.). Thermal imaging presents a big potential in terms of monitoring the wheel-rail interaction and can also be used to identify flange climbing, rolling noise generation or longitudinal creepage during traction or braking.
1 July 2012 in Key Engineering Materials
Light rail systems have now their great return in many European cities carrying an increasing number of people every year. This increasing trend requires suitable operation and maintenance standards for both vehicle and track. Furthermore, in order to make a public transport competitive to private transport, its very important to increase safety and ride comfort for passengers. The aim of the presented work was to determine the suitable vibration-based symptoms for the identification of a light rail vehicle technical state, as well as the development of appropriate methodology to use the information contained therein. Both simulation and experimental phase are described. The present analysis is focused mainly on the suspension state monitoring, but some others failures were also considered.