Omni-directional, ultra-small-angle x-ray scattering imaging provides a method to measure the orientation of micro-structures without having to resolve them. In this letter, we use single-photon localization with the Timepix3 chip to demonstrate, to the best of our knowledge, the first laboratory-based implementation of single-shot, omni-directional x-ray scattering imaging using the beam-tracking technique. The setup allows a fast and accurate retrieval of the scattering signal using a simple absorption mask. We suggest that our new approach may enable faster laboratory-based tensor tomography and could be used for energy-resolved x-ray scattering imaging.
26 October 2018 in Journal of Synchrotron Radiation
Near Infrared hyperspectral imaging (HSI) offers a fast and non-destructive method for seed quality assessment through combining spectroscopy and imaging. Recently, convolutional neural networks (CNN) have shown to be promising tools for red-green-blue (RGB) image or spectral cereal classification. This paper describes the design and implementation of deep CNN models capable of utilizing both the spatial and spectral dimension of HSI data simultaneously for analysis of bulk grain samples with densely packed kernels. Classification of eight grain samples, including six different wheat varieties, were used as a test case. The study shows that the CNN architecture ResNet, originally designed for RGB images, can be adapted to use the full spatio-spectral dimension of the HSI data through adding a linear down sample layer prior to the conventional ResNet architecture. Using traditional spectral pre-processing methods before passing the data to the CNN does not improve the classification accuracy of the networks, while a channel-wise image standardization improves the accuracy significantly. The modified ResNet applied to the full spatio-spectral dimension has a classification accuracy of up to 99.75 ± 0.02%, outperforming both purely spectral (86.5 ± 0.1%) and purely spatial (98.70 ± 0.01%) based methods in terms of accuracy, indicating that utilizing spatio-spectral correlation can improve sample classification, but also that grain classification is primarily solved using spatial information. The findings reported in this paper demonstrate how CNN networks can be designed to leverage spatio-spectral information in hyperspectral data. The combination of HSI and spatio-spectral CNN networks shows a possible method for fast prediction of bulk grain quality parameters where both spectral and spatial properties of the grains are important.
The simultaneous retrieval of x-ray attenuation, phase, and scattering using multimodal imaging techniques is finding increasing use in a range of applications, from medicine to materials science. Most techniques rely on the mechanical movement of an optical element (e.g., a grating or a mask) to obtain the multimodal images. While single-shot approaches exist, they typically employ detector pixels smaller than the grating period, often with low detection efficiency, and are limited in resolution unless either the sample or the optical element is displaced in various positions and multiple frames are collected. In this paper, we replace mechanical motion with the MÖNCH detector's capability to reach sub-pixel resolutions by interpolating between neighboring pixels collecting the charge generated by a single x-ray event. This enabled us to obtain the pilot demonstration of a laboratory-based high-resolution, single-shot multimodal imaging technique capable of simultaneously retrieving attenuation, directional differential phase, and scatter images, without any mechanical movement. We show that our proof-of-concept setup enables a single-shot resolution of 19.5 and that the resulting images provide sufficient information to produce a reliable sample thickness map. Furthermore, we demonstrate that the setup is capable of producing single-shot directional scattering images, while leaving open the option to further increase the resolution by using sample dithering.
Compared to the dual-energy scintillator detectors widely used today, energy-resolved photon-counting x-ray detectors show the potential to improve material identification in various radiography and tomography applications used for industrial and security purposes. However, detector effects, such as charge sharing and photon pileup, distort the measured spectra in pixelated, photon-counting detectors operating under high flux. These effects result in a significant performance degradation of the detectors when used for material identification where accurate spectral measurements are required. We have developed a semianalytical, postdata acquisition, computational algorithm that corrects the measured attenuation curve for severe spectral distortions caused by the detector. The calibration of the algorithm is based on simple attenuation measurements of commercially available materials using standard laboratory sources, enabling the algorithm to be used in any x-ray setup. The algorithm is developed for correcting spectral data acquired with the MultiX ME100 CdTe x-ray detector but could be adapted with small adjustments to other photon-counting, energy-resolved detectors with CdTe sensors. The validation of the algorithm has been done using experimental data acquired with both a standard laboratory source and synchrotron radiation. The experiments show that the algorithm is fast, reliable at x-ray flux up to 5 Mph / s / mm2 and greatly improves the accuracy of the measured spectrally resolved linear attenuation, making the algorithm useful for both security and industrial applications where photon-counting detectors are used.