The surface condition of an implant has a significant impact on response occurring at the implant-biosystem border. The knowledge of physical-chemical and biological processes allows for targeted modification of biomaterials to induce a specified response of a tissue. The present research was aimed at development of technology composing of obtaining the nanotube oxide layers on a porous titanium alloy Ti13Nb13Zr, followed by the deposition of phosphate coating. The porous substrate (porosity about 50%) was prepared by a selective laser melting of the Ti13Nb13Zr powder with the SLM Realizer 100 equipment. The nanotubular oxide layers were fabricated by electrochemical oxidation in H3PO4 + 0.3% HF mixture for 30 min. at a constant voltage of 20V. The calcium phosphate coatings were formed by the electrochemically assisted deposition (ECAD). The presence of nanotubular oxide layers with their internal diameters ranging from 30 to 100 nm was observed by SEM (JEOL JSM-7600F). The nanotubes have dimensions that facilitated the deposition of hydroxyapatite.
The properties of chitosan coatings on titanium surfaces may be influenced by a variety of factors, including their chemical characteristics and the deposition method. The aim of this research was to determine the influence of a chitosan’s origin (a type of shrimp) and deacetylation degree (DD), when deposited on a very smooth titanium surface, on adhesion and biological behavior. The tests were performed using chitosan of a degree of 87% or 84% of deacetylation and that originated from armor crabs or shrimp armor. The technology of fabrication of chitosan coatings was by surface polishing to a smooth surface, oxidation in air, and immersion in a chitosan solution. The surface topographies were analyzed with an atomic force microscope and their water contact angles were measured by a falling drop method with a goniometer. The bioactivity tests were done in in vitro on osteogenic cells, type MC3T3-E1, with a biological microscope. The abrasion of the coatings was examined using a nano tribotester. The obtained results revealed that the adhesion of the coatings onto a smooth, oxidized titanium surface is appropriate as they remain sufficiently adjacent to the surface after wear tests. The source of chitin has a significant influence on biological properties, and the deacetylation degree is much less critical. The performed tests demonstrated the crucial role that the source of chitosan and the applicability of the applied surface treatment play in the preparation of chitosan coatings.
Sciendo provides publishing services and solutions to academic and professional organizations and individual authors. We publish journals, books, conference proceedings and a variety of other publications.
In order to size a temporomandibular joint prosthesis based on an innovative concept, this study characterizes the trabecular bone tissue geometry within the joint. The main objective consists of taking into account the inter-variability of the trabecular bone volume to design a modular, even customized, innovative mandibular implant. A non-invasive method was used to describe bone tissue distribution. It involves measuring geometrical characteristics of the temporomandibular joint from computerized tomography scans using an easy and quick protocol and open-source software. The measurements performed on the scans of 68 patients showed that this high-precision method is also user-dependent. Lastly, we built value ranges to set the dimensions of a prosthesis prototype and point out a large inter-individual variability for each measurement and a low correlation between bone tissue distribution and age or gender. The software package gives precise measurements for the different parameters studied. However, the automation of the delineation of the area of trabecular bone should improve reproducibility. Also, the protocol can be applied to other medical specialties. Used in the context of a design for an innovative temporomandibular joint prosthesis, it points out a strong inter-individual heterogeneity in the distribution of bone tissue, which leads to prefer a modular implant design.
При определении размеров инновационного эндопротеза височно-нижнечелюстного сустава необходимо учитывать характеристики трабекулярной костной ткани в области сустава. Задача исследования заключалась в учете варьирования объема трабекулярной кости для проектирования модульного, персона-лизированного, инновационного имплантата мыщелка височно-нижнечелюстного сустава. Для описания распределения плотности костной ткани применялся неинвазивный метод, который включает в себя измерение геометрических параметров височно-нижнечелюстного сустава по данным снимков компьютерной томографии с использованием программного обеспечения с открытым исходным кодом. Изме-рения, выполненные на снимках 68 пациентов, показали зависимость высокоточного метода от оператора. Установлены диапазоны значений для определения размеров прототипа эндопротеза и выявлена значительная индивидуальная вариация каждого измеряемого параметра, а также слабая корреляция между распределением плотности костной ткани и возрастом/полом пациента. Применяемое программное обеспечение позволяет проводить точное измерение исследуемых параметров. В перспективе планируется добавление автоматизации определения области трабекулярной кости, что позволит повысить воспроизводимость метода. Кроме того, разработанный метод может быть внедрен и в другие медицинские исследования. На основе методики оценки трабекулярной ткани при разработке инновационного протеза височно-нижнечелюстного сустава было выявлена выраженная индивидуальная неоднородность распределения кости, что обуславливает предпочтительность модульной конструкции имплантата.