Due to their functional and biological benefits, shape memory polymer (SMP) stents have attracted the attention of researchers in the biomedical science area. The highlights of this article are the evaluation of stent performance including radial force recovery and recovery start temperature (RST) in a constrained state. The effects of polyurethane (PU) mechanical properties and fabrication method are investigated on thermo-viscoelastic properties, sample defect and shape recovery of PU and polycaprolactone (PCL) blend. Thereafter, three tubular stents fabricated with the different diameter to thickness ( d / t ) ratio and their mechanical behavior are examined in loading, relaxation, and unloading. Finally, the radial force recovery of the stents is measured after stimulation in temperatures up to 45 °C. Emerging more peaks in the delta tangent graph implies that samples fabricated with solution-mixing has a better viscoelastic behavior and shows fewer defects compared to the melt-mixing ones. The fabrication method was much more effective on enhancement of the storage and loss modulus compared to double increasing of Young’s modulus of applied PU from 4.3 to 9 MPa. Moreover, an increase in the stent’s d / t from 15 to 10 causes not only an increase in the radial stiffness and force recovery but also leads to the reduction of irreversible deformation and RST. The results of this research reveals the importance of the dimensional and geometric design of SMP stents in controlling the force recovery and RST.
8 October 2018 in Journal of Intelligent Material Systems and Structures
Shape memory polymer composites have attracted significant attention due to novel properties and great applications. In this article, we focus on the fabrication and simulation of polyurethane/polycaprolactone nanocomposites. The polyurethane/polycaprolactone blends containing ZnO nanoparticles (5 to 30 wt%) are fabricated using a solution mixing and casting method. It is found that significant improvement of polyurethane/polycaprolactone composites in Young’s modulus is achieved by incorporating 20 wt% of ZnO nanoparticles; also, the results of the shape recovery ratio reveal that adding an optimum amount of ZnO (the reinforcement) can increase the shape recovery ratio (for 20 wt% of ZnO). These results could most likely be explained by the fact that some particles restrict the hard segment–soft segment interactions and provide more mobility to polycaprolactone components, while the other nanoparticles can act as the nucleating agent for polycaprolactone chains. A generalized Maxwell model is then used to examine the shape memory behavior of shape memory polymer composites. The dynamic mechanical thermal analysis results are utilized to define the model coefficients and the simulation is carried out to determine the shape recovery ratio. Simulation of this shape recovery ratio for shape memory polymer composites reveals that the numerical results are in good agreement with those of the experimental data.
9 June 2017 in International Journal of Damage Mechanics
The present work aims to obtain failure loads for open-hole unidirectional composite plates under tensile loading. For this purpose, a user-defined material model in the finite element analysis package, ABAQUS, was developed to predict the failure load of the open-hole composite laminates using progressive failure analysis. Hashin and modified Yamanda-Sun’s failure criteria with complete and Camanho’s material degradation model are studied. In order to achieve the most accurate predictions, the influence of failure criteria and property degradation rules are investigated and failure loads and failure modes of the composites are compared with the same experimental test results from literature. A good agreement between experimental results and numerical predictions was observed.
Mimicking microvascular tissue microenvironment in vitro calls for a cytocompatible technique of manufacturing biocompatible hollow microfibers suitable for cell‐encapsulation/seeding in and around them. The techniques reported to date either have a limit on the microfiber dimensions or undergo a complex manufacturing process. Here, a microfluidic‐based method for cell seeding inside alginate hollow microfibers is designed whereby mouse astrocytes (C8‐D1A) are passively seeded on the inner surface of these hollow microfibers. Collagen I and poly‐d‐lysine, as cell attachment additives, are tested to assess cell adhesion and viability; the results are compared with nonadditive‐based hollow microfibers (BARE). The BARE furnishes better cell attachment and higher cell viability immediately after manufacturing, and an increasing trend in the cell viability is observed between Day 0 and Day 2. Swelling analysis using percentage initial weight and width is performed on BARE microfibers furnishing a maximum of 124.1% and 106.1%, respectively. Degradation analysis using weight observed a 62% loss after 3 days, with 46% occurring in the first 12 h. In the frequency sweep test performed, the storage modulus (G′) remains comparatively higher than the loss modulus (G″) in the frequency range 0–20 Hz, indicating high elastic behavior of the hollow microfibers.
In this paper, shape memory polymers (SMPs) are fabricated by blending Polyurethane (PU) and Polycaprolactone (PCL). A novel method is used to make tubular stents using this blend. The solution coating method is applied to fabricate the SMP stent samples with a non-groove structure. Some metallic commercial stents made of the platinum-chromium alloy are used to compare SMP stents’ the mechanical properties with metal ones. According to the stents’ functionality, two mechanical tests, i.e., radial compression and three-point bending, are conducted in a range of body temperature. According to the mechanical test results, the tubular polymer stent shows a lower strength under the radial forces and a higher strength under the bending forces than to their metal counterparts. However, the mechanical properties of the SMP stents are in the range of metal stents. Thus, the PU/PCL SMP blend can be a promising candidate to be used as the coronary artery stents.