Transparent anti-fogging and self-cleaning coatings are of great interest for many applications, including solar panels, windshields and displays or lenses to be used in humid environments. In this paper, we report on the simultaneous synthesis, at atmospheric pressure, of anatase TiO2 nanoparticles and low-temperature, high-rate deposition of anatase TiO2/SiO2 nanocomposite coatings. These coatings exhibit durable super-hydrophilic and photocatalytic properties. The strategy followed relies on concomitant and separated injections of titania, i.e. titanium isopropoxide, and silica, i.e. hexamethyldisiloxane, precursors in the stream of a blown-arc discharge to form transparent anti-fogging and self-cleaning anatase TiO2/SiO2 nanocomposite coatings on polymer substrates.
Herein, we report the impact of plasma on gold nanoparticles synthesis. We used an atmospheric plasma torch fed with an aerosolized tetrachloroauric(III) acid trihydrate (HAuCl4·3H2O) solution. The investigation showed that using pure ethanol as a solvent for the gold precursor enabled a better dispersion compared to a water-containing solution. We demonstrated here that the deposition parameters are easy to control, presenting the influence of solvent concentration and deposition time. The advantage of our method is that no capping agent was used. We assume that plasma creates a carbon-based matrix around the gold nanoparticles preventing them to agglomerate. The XPS results revealed the impact of using plasma. Metallic gold was detected in the plasma-treated sample, whereas the no-plasma sample revealed only Au(I) and Au(III) contributions originating from the HAuCl4 precursor. Detailed HRTEM, EDS mapping, and SAED analyses led to more insights into the structure.
Gallium-doped zinc oxide (GZO) films were fabricated using RF magnetron sputtering and atomic layer deposition (ALD). The latter ones demonstrate higher electrical conductivities (up to 2700 S cm-1) and enhanced charge mobilities (18 cm2 V-1 s-1). The morphological analysis reveals differences mostly due to the very different nature of the deposition processes. The film deposited via ALD shows an increased transmittance in the visible range and a very small one in the infrared range that leads to a figure of merit of 0.009 Ω-1 (10 times higher than for the films deposited via sputtering). A benchmarking is made with an RF sputtered indium-doped tin oxide (ITO) film used conventionally in the industry. Another comparison between ZnO, Al:ZnO (AZO), and Ga:ZnO (GZO) films fabricated by ALD is presented, and the evolution of physical properties with doping is evidenced. Finally, we processed GZO thin films on a glass substrate into patterned transparent patch antennas to demonstrate an application case of short-range communication by means of the Bluetooth Low Energy (BLE) protocol. The GZO transparent antennas' performances are compared to a reference ITO antenna on a glass substrate and a conventional copper antenna on FR4 PCB. The results highlight the possibility to use the transparent GZO antenna for reliable short-range communication and the achievability of an antenna entirely processed by ALD.
23 April 2014 in Journal of Physics D: Applied Physics
Crystalline and electrocatalytically active cobalt oxide (Co3O4) thin films were successfully synthesized under open-air conditions using atmospheric pressure plasma-enhanced chemical vapor deposition (AP-PECVD) with the Co(acac)3 precursor. This study explored the influence of process parameters on the composition, crystallinity, and quality of the resulting thin films. It was found that the substrate temperature had a negligible effect due to the inherent heating by the plasma afterglow. The presence of atmospheric oxygen was identified as crucial for forming Co3O4 thin films and eliminating residual impurities such as carbon and nitrogen, as demonstrated by experiments in O2-free environments. The formation of Co3O4 was attributed to radical-mediated reactions, where the reactive species generated in the plasma interacted with oxygen-rich molecules from the surrounding air. These findings provide valuable insights into the deposition mechanisms and catalytic potential of Co3O4 thin films synthesized via AP-PECVD.
This work focuses on the fabrication of transparent piezoelectric transducers on glass substrates for ultrasonic actuation. Transparent Lead Titanate Zirconate (PZT) thin films are grown on glass following a sol-gel route and InterDigital Electrodes (IDE) patterned by photolithography. The electrodes design aims to optimize the volume of active piezoelectric material together with the transparency of the actuator stack. The actuator is used in d33 mode offering high transduction capabilities, while the IDE design allows for increasing the area of the actuator in the cm2 range. The results demonstrate that fully transparent actuators with ultrasonic range resonant frequency (~100kHz) can be fabricated on glass substrates. Direct applications of these actuators are haptic devices for tactile sensation of surface roughness.