A latch-type comparator with a dynamic bias pre-amplifier is implemented in a 65-nm CMOS process. The dynamic bias with a tail capacitor is simple to implement and ensures that the pre-amplifier output nodes are only partially discharged to reduce the energy consumption. The comparator is analyzed and compared to its prior art in terms of energy consumption and input referred noise voltage. First-order equations are presented that show how to optimize the pre-amplifier for low noise and high gain. Both the dynamic bias comparator and the prior art are implemented on the same die and measurements show that the dynamic bias can reduce the average energy consumption by about a factor 2.5 for the same input-equivalent noise at an input common-mode level of half the supply voltage.
9 March 2021 in IEEE Journal of Solid-State Circuits
Crystal oscillators can be started up quickly by using energy injection techniques. However, the generation of the injection waveform, as well as driving the large capacitive load formed by the crystal, costs a large amount of energy. This article applies the concept of stepwise charging to reduce the energy required to drive the crystal. The energy required to generate the injection waveform by self-timed injection is reduced by using a discrete-time dynamic-bias comparator which uses a simple offset calibration method. Furthermore, the bridge switch resistance is varied dynamically through self-timed control logic to alleviate the accuracy-speed tradeoff. A prototype was manufactured in a 65-nm (triple-well) CMOS technology, which was tested with various crystals ranging from 24 to 50 MHz, improving upon the state of the art in energy consumption.
21 March 2023 in IEEE Transactions on Circuits and Systems II: Express Briefs
DAC mismatch is a major challenge for high-resolution ADCs. This paper proposes an analog-detection-based input range compensation technique for high-resolution ADCs with mismatch error shaping (MES). By applying a pre-comparison and suitably switching the DAC MSB, the input loss caused by MES is compensated. By adopting a flying-capacitor sampling technique, the prediction errors found in prior solutions are avoided. The prototype 14-bit SAR ADC achieves 80.4 dB SNDR and 93 dB SFDR in a 4 kHz signal bandwidth with an OSR of 16. It only occupies 0.0034 mm and consumes 0.656 μW under a 0.8 V supply, leading to a Schreier figure-of-merit of 178.3 dB. These features make it suitable for miniaturized high-performance IoT and biomedical systems.
5 February 2025 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper describes the design and implementation of a 4 MHz bandwidth 3rd-order Discrete-Time (DT) Passive Delta-Sigma Modulator (PM), which avoids the use of supply voltage-sensitive linear amplifiers. The Switched-Capacitor (SC) operation and amplifier-less nature of its loop filter render the proposed modulator highly supply voltage-and clock frequency-flexible. To explain our design choices, we investigate two key design challenges unique to PMs. Firstly, the noise criticality of the quantizer ADC due to the lack of (voltage) gain in the loop filter preceding it. Secondly, the inaccessibility of the readily synthesizable and highly frequency-selective loop filter frequency responses typically employed in Ms, caused by the absence of linear amplifiers. We show that the noise-power trade-off of the quantizer ADC in 1 bit P$\Delta \Sigma$Ms is the same as that of the first integrator amplifier in Active M. Next, we cover the suitability of several passive filters for use in PM loops. This leads to the selection of the voltage-sampled Charge-Rotating IIR (CR-IIR) filter, for which we show M-oriented design equations, on which we base the design of our 3rd-order DT PM. Measurement results on the resulting prototype PM, implemented in GlobalFoundries 22 nm FD-SOI CMOS, demonstrate that it achieves a 71.9 dB peak SNDR and 4 MHz bandwidth while consuming 4.4 mW from a 0.9 V supply and occupying 0.076mm$^\mathrm{\bf 2}$ of silicon area. The prototype PM continues to operate at a 2.25$\times$ reduced supply voltage of 0.4 V, albeit at a reduced bandwidth of 156.25 kHz, where it achieves a peak SNDR of 62 dB while consuming 37.8 $\mu$W.
7 December 2021 in IEEE Transactions on Circuits and Systems I: Regular Papers
A novel algorithm is presented that can resolve frequency ambiguity that arises from sampling a set of signals spanning more than a single Nyquist zone. The method uses two samplers, each sampling the same input signal with different (non-integer multiple) sampling rates. The algorithm is able to resolve frequency ambiguity and reconstruct signals with an orthogonal frequency basis spanning multiple Nyquist zones, provided that the aggregate information-bearing bandwidth of the signals is less than half the cumulative data converter sampling rates. This manuscript describes the theoretical background for the algorithm and validates it through measurements performed on a test-board comprising of two 10 bit analog-to-digital converters clocked at two different (non-integer multiple) sample rates. Measurements show that even in the presence of aliasing, an orthogonal signal spanning multiple Nyquist zones can be fully reconstructed.
29 October 2024 in IEEE Journal of Solid-State Circuits
A programmable intermediate frequency (IF) receiver is proposed, employing a sampler, time-varying capacitor, and switched-capacitor integrator. It realizes high-order finite impulse response (FIR) low-pass or bandpass filtering (BPF) and frequency translation with harmonic rejection (HR). The receiver’s center frequency and bandwidth (BW) can be independently programmed across the Nyquist zone. The primary focus is on balancing filter stopband rejection with harmonic, image, and alias rejection in a prototype 28 nm CMOS chip design. This work is also the first to address and quantify the adjacent and alternate adjacent channel aliasing in filtering by aliasing filters. The center frequency and BW of the receiver can be programmed to 0–1 GHz and 8–25 MHz, respectively. The receiver achieves a wideband impedance matching S $_{11}$$<$$-$ 9 dB across the first Nyquist zone. It employs 8-bit filter coefficients to achieve consistent $>$ 50 dB stopband attenuation at 1 $\times$ BW offset, HR, image rejection (IR), and 50 dB in-band (IB) alias suppression. The I and Q receivers use only a single fixed 1 GHz clock frequency to achieve all the functionality and consume 73.6 mW.