1 May 2024 in Journal of Instrumentation
The ATLAS detector is installed in its experimental cavern at Point 1 of the CERN Large Hadron Collider. During Run 2 of the LHC, a luminosity of ℒ = 2 × 1034 cm-2 s-1 was routinely achieved at the start of fills, twice the design luminosity. For Run 3, accelerator improvements, notably luminosity levelling, allow sustained running at an instantaneous luminosity of ℒ = 2 × 1034 cm-2 s-1, with an average of up to 60 interactions per bunch crossing. The ATLAS detector has been upgraded to recover Run 1 single-lepton trigger thresholds while operating comfortably under Run 3 sustained pileup conditions. A fourth pixel layer 3.3 cm from the beam axis was added before Run 2 to improve vertex reconstruction and b-tagging performance. New Liquid Argon Calorimeter digital trigger electronics, with corresponding upgrades to the Trigger and Data Acquisition system, take advantage of a factor of 10 finer granularity to improve triggering on electrons, photons, taus, and hadronic signatures through increased pileup rejection. The inner muon endcap wheels were replaced by New Small Wheels with Micromegas and small-strip Thin Gap Chamber detectors, providing both precision tracking and Level-1 Muon trigger functionality. Trigger coverage of the inner barrel muon layer near one endcap region was augmented with modules integrating new thin-gap resistive plate chambers and smaller-diameter drift-tube chambers. Tile Calorimeter scintillation counters were added to improve electron energy resolution and background rejection. Upgrades to Minimum Bias Trigger Scintillators and Forward Detectors improve luminosity monitoring and enable total proton-proton cross section, diffractive physics, and heavy ion measurements. These upgrades are all compatible with operation in the much harsher environment anticipated after the High-Luminosity upgrade of the LHC and are the first steps towards preparing ATLAS for the High-Luminosity upgrade of the LHC. This paper describes the Run 3 configuration of the ATLAS detector.
4 June 2021 in IEEE Transactions on Nuclear Science
We present the design and test results of a time-to-digital-converter (TDC). The TDC will be a part of the readout Application-Specific Integrated Circuit (ASIC), called endcap timing read-out chip (ETROC), to read out low-gain avalanche detectors (LGADs) for the CMS endcap timing layer (ETL) of high-luminosity large hadron collider (LHC) upgrade. One of the challenges of the ETROC design is that the TDC is required to consume less than 200 μW for each pixel at the nominal hit occupancy of 1%. To meet the low-power requirement, we use a single delay line for both the time of arrival (TOA) and the time over threshold (TOT) measurements without delay control. A double-strobe self-calibration scheme is used to compensate for process variation, temperature, and power supply voltage. The TDC is fabricated in a 65-nm CMOS technology. The overall performances of the TDC have been evaluated. The TOA has a bin size of 17.8 ps within its effective dynamic range of 11.6 ns. The effective measurement precision of the TOA is 5.6 and 9.9 ps with and without nonlinearity correction, respectively. The TDC block consumes 97 μW at the hit occupancy of 1%. Over a temperature range from 23 °C to 78 °C and a power supply voltage range from 1.05 to 1.35 V (the nominal value of 1.20 V), the self-calibrated bin size of the TOA varies within 0.4%. The measured TDC performances meet the requirements except that more tests will be performed in the future to verify that the TDC complies with the radiation tolerance specifications.
1 April 2019 in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
7 May 2019 in IEEE Transactions on Nuclear Science
We present the design and the test results of a dual-channel vertical-cavity surface-emitting laser (VCSEL) driver application-specific integrated circuit (ASIC) LOCld65 for detector front-end readout. LOCld65 is designed in a commercial 65-nm CMOS technology with a power supply of 1.2 V. LOCld65 contains two separate channels with the same structure and the two channels share an I 2 C slave. Each channel consists of an input amplifier, four stages of limiting amplifiers (LAs), a high-current output driver, and a bias-current generator. In order to extend the bandwidth, the input amplifier uses an inductive peaking technique and the LAs use a shared inductive peaking technique. The input amplifier and the output driver each utilize a continuous-time linear equalizer (CTLE). The LAs employ active feedback. The modulation current, the bias current, the peaking strength of the CTLEs, and the feedback strength of LAs are programmable through an I 2 C interface. In order to protect from the radiation damage, the I 2 C slave is implemented with triple modular redundancy. Each channel of LOCld65 is tested to operate up to 14 Gb/s with typical power dissipations (the VCSEL included) of 68.3 and 62.1 mW/channel at the VCSEL voltages of 3.3 and 2.5 V, respectively. LOCld65 survives 4.9 kGy(SiO 2 ). LOCld65 is an excellent match for the serializer-deserializer ASIC low power giga bit transceiver in single- or dual-channel optical transmitters in high-luminosity Large Hadron Collider (HL-LHC) upgrade applications.
13 January 2023 in IEEE Transactions on Nuclear Science
This paper presents the design and test results of a 14-Gbps Vertical-Cavity Surface-Emitting Laser (VCSEL) driving ASIC based on a commercial 65 nm CMOS technology with a novel power efficient driving structure. This VCSEL driver consists of an input equalizer stage, a pre-driver stage, an output driver stage, and their bias circuits. The equalizer stage uses the continuous time linear equalizer (CTLE) structure to compensate for the high-frequency attenuation. The pre-driver stage is composed of two stage limiting amplifiers with a shared inductor structure. The proposed output driver stage adopts a novel complementary-modulated method to fully utilize the currents in both branches of the conventional differential structure. In addition, a self-adjusting CTLE pre-emphasis with edge peaking function is combined in the output stage to improve the bandwidth and boost the falling edge of the output current signal. This VCSEL driving ASIC has been fully tested with a real VCSEL load, and the wide-open optical eye diagrams have been captured at a 14-Gbps data rate with a power consumption of 44 mW. The peak-to-peak jitter of the 14-Gbps optical eye diagram is 15.8 ps with a random jitter of 3.02 ps.
1 August 2021 in Journal of Instrumentation
We present the characterization and quality control test of a gigabit cable receiver ASIC prototype, GBCR2, for the ATLAS Inner Tracker pixel detector upgrade. GBCR2 equalizes and retimes the uplink electrical signals from RD53B through a 6 m Twinax AWG34 cable to lpGBT. GBCR2 also pre-emphasizes downlink command signals through the same electrical connection from lpGBT to RD53B. GBCR2 has seven uplink channels each at 1.28 Gbps and two downlink channels each at 160 Mbps. The prototype is fabricated in a 65 nm CMOS process. The characterization of GBCR2 has been demonstrated that the total jitter of the output signal is 129.1 ps (peak-peak) in the non-retiming mode or 79.3 ps (peak-peak) in the retiming mode for the uplink channel and meets the requirements of lpGBT. The total power consumption of all uplink channels is 87.0 mW in the non-retiming mode and 101.4 mW in the retiming mode, below the specification of 174 mW. The two downlink channels consume less than 53 mW. A quality control test procedure is proposed and 169 prototype chips are tested. The yield is about 97.0%.