5 April 2022 in Journal of Lightwave Technology
We present a study into the gas pressure and composition within a hollow core optical fiber immediately after fabrication. Results from three different experimental techniques indicate that the initial absolute pressure inside of the hollow core is significantly lower than atmospheric pressure. By measuring the equilibrium height to which water ingresses into the hollow core, we estimate the absolute internal gas pressure to be 20 kPa < ${{\boldsymbol{P}}_{\boldsymbol{i}}}$ < 29 kPa for the fibers reported here that were fabricated using standard techniques. The initial gas composition within the hollow core was studied using Raman and absorption spectroscopy and the evolution of the gas composition provides indirect information about the condition of the silica surfaces inside the fiber. The measurements indicate that these internal surfaces become saturated with atmospheric water vapor as this is drawn into the open-ended fiber, initially due to a pressure gradient post-fabrication. Our findings are an essential foundation for the study of long-term optical and mechanical performance of hollow core fibers and important for accurate characterization of these specialty fibers. The first is becoming increasingly important as commercial applications of these fibers expand.
9 November 2022 in Optics Express
We demonstrate recent progress in the development of a Raman gas sensor using a single cladding ring anti-resonant hollow core micro-structured optical fiber (HC-ARF) and a low power pump source. The HC-ARF was designed specifically for low attenuation and wide bandwidth in the visible spectral region and provided low loss at both the pump wavelength (532 nm) and Stokes wavelengths up to a Raman shift of 5000 cm−1. A novel selective core pressurization scheme was also implemented to further reduce the confinement loss, improving the Raman signal enhancement by a factor of 1.9 compared to a standard fiber filling scheme. By exploiting longer lengths of fiber, direct detection of both methane and hydrogen at concentrations of 5 and 10 ppm respectively is demonstrated and a noise equivalent limit-of-detection of 0.15 ppm is calculated for methane.
7 May 2024 in IEEE Journal of Selected Topics in Quantum Electronics
Recent progress in reducing the loss of hollow-core fibres (HCFs) makes them great candidates for many fibre applications. However, as the fibre's optical properties depend on the gas pressure and composition within the core and cladding holes, it is essential to understand the gas dynamics at play when the fibres are pressurised, vented or evacuated. Here, we investigate the gas flow dynamics along the core of an HCF with a more complex microstructure design, as is typical of recent state-of-the-art HCFs. We use a novel distributed technique based on optical time-domain reflectometry (OTDR). This technique enables measurement of the evolution of the pressure distribution within the hollow core during the gas-filling process over long fibre lengths. Using these results, we show that the pressure distribution inside the HCF can be simulated using simplified Navier-Stokes equations and approximating the fibre core as a simple cylindrical tube of $\sim$ 0.7 times the fibre core diameter.
20 May 2024 in Optics Express
When a hollow core fiber is drawn, the core and cladding holes within the internal cane geometry are pressurized with an inert gas to enable precise control over the internal microstructure of the fiber and counteract surface tension forces. Primarily by considering the temperature drop as the fiber passes through the furnace and the geometrical transformation of the internal microstructure from preform-to-fiber, we recently established that the gas pressure within the final ‘as-drawn’ fiber is substantially below atmospheric pressure. We have also established that slight changes in the gas refractive index within the core and surrounding cladding holes induced by changes in gas pressure are sufficient to significantly affect both the modality and loss of the fiber. Here we demonstrate, through both simulations and experimental measurements, that the combination of these effects leads to transient changes in the fiber’s attenuation when the fibers are opened to atmosphere post-fabrication. It is important to account for this phenomenon for accurate fiber characterization, particularly when long lengths of fiber are drawn where it could take many weeks for every part of the internal microstructure to reach atmospheric pressure.
1 March 2001 in Acta Astronautica
24 April 2026 in Photonics Research
Low-frequency acoustic waves exhibit low attenuation and strong penetration, enabling propagation over long distances in water and the solid Earth. This capability underpins applications in natural-hazard monitoring and early warning (earthquakes, tsunamis, volcanic activity), long-range marine sensing and surveillance, and structural and equipment-health monitoring in harsh environments. Traditional piezoelectric hydrophones suffer from high self-noise and electro-magnetic interference, motivating the exploration of fiber optic solutions. However, the operation of fiber solutions at low frequencies suffers from temperature cross-sensitivity due to the inherent thermal sensitivity of conventional optical fibers. Hollow-core fibers (HCFs), which guide light in air/vacuum, provide lower thermal and higher acoustic sensitivity than conventional solid core fibers; however, the extent to which they could address this limitation has never been studied. Here, we present a comprehensive study of the acoustic and thermal sensitivities of HCFs, combining theoretical modeling and experimental validation, aiming for high acoustic sensitivity while keeping thermal sensitivity low, hence reducing unwanted cross-sensitivity. We validate its results experimentally on three HCFs with different structural compositions, quantifying the trade-off between acoustic and temperature sensitivities. Besides, we demonstrate a substantial improvement in temperature–acoustic decoupling by employing an HCF made from Ti-doped ultralow-expansion (ULE) glass, achieving a reduction in thermal sensitivity by more than three orders of magnitude compared with standard single-mode fiber while maintaining comparable acoustic sensitivity. Further, based on the theoretical model we have developed, we show that more optimal coating material could improve the performance of ULE-HCF by another two orders of magnitude. This work thus guides comprehensive design of thermally stable and acoustically sensitive HCF sensors for low-frequency acoustic sensing.