The injection of electron cyclotron (EC) waves fulfills a number of important tasks in nuclear fusion devices for which detailed knowledge of the spatial power deposition profile is critical. This deposition profile is commonly determined using forward models such as beam or ray tracing. Recent numerical and experimental studies have shown that small-angle scattering of the EC beam as it passes through the turbulent plasma edge can cause significant broadening of the effective deposition profile, leading to considerable underestimation of the deposition width by forward methods. However, traditional inverse methods to determine the deposition profile from measurements overestimate the deposition profile width due to transport broadening. In this work, we implement three novel methods to resolve the EC power deposition profile from measurements that counteract transport broadening by simultaneously resolving transport and power deposition. We validate their assumptions and compare the results from these methods to the traditional break-in-slope method as well as to the TORAY ray-tracing code in a set of DIII-D discharges spanning five different confinement modes. We show that the four different inverse methods, novel and established, paint a consistent picture of deposition broadening. Specifically, we show that the measured power deposition profile is between 1.6 and 3.6 times wider than the TORAY profiles. Moreover, we show the considerable consequences that this level of broadening can have for ITER.
The shape of a plasma meniscus is a key factor to determine the beam focusing. The physics model of the meniscus formation for hydrogen negative ion sources has not been established yet. A backward trajectory calculation based on experimental observation is performed in order to derive the particle information at the meniscus. It is observed that the negative ion density is spatially nonuniform in the direction parallel to the magnets for suppression of co-extracted electrons. A nonuniformity of the negative ion density in the vicinity of the meniscus is taken into account in the forward trajectory calculation. It reveals that the nonuniform negative ion distribution leads to degradation of the beam focusing and the beam splitting in phase space. The importance of the spatial distribution of negative ions on meniscus modelling is discussed with a comparison to uniform extraction model.
The flux fit method is used to self-consistently estimate the power deposition profile and heat transport profiles from temperature measurements originating from perturbative experiments with a modulated source. This Letter improves on this method by addressing the limitations and assumptions. The most crucial improvement is the additional freedom in the source deposition profile. Allowing for a variable central deposition location and height and including a skewness parameter produces deposition profiles more consistent with the measurement data, but still wider than equilibrium ray tracing in two different DIII-D discharges. Moreover, we show that the quality of the estimated deposition profile is key to the accuracy of diffusivity and convectivity estimates, but inversely, the estimated transport parameters hardly affect the quality of the power deposition estimate. Using this method, we show that the power deposition profile estimate is broadened with respect to ray-tracing by about 1.7–1.8 times in two DIII-D discharges.
The understanding of the time-scales and associated transient behavior of fusion exhaust plasmas plays a crucial role in its dynamic modeling and its control. This work presents an overview of experimental investigations of the exhaust dynamics in TCV, MAST-U, ASDEX-Upgrade, WEST, DIII-D, and JET. From the presented experiments, a clear picture arises on properties of the exhaust dynamics across machines. Particularly, we observe that the scrape-off layer equilibrates on fast time-scales ( 70 Hz) and that exhaust dynamics measured in response to gas valve modulations mostly behave smoothly and linearly, with similarities across devices, across scenarios (H-mode, L-mode), injected species, and injection locations. The measurements presented have formed the basis for systematic exhaust control on the considered devices. We now present this database for the essential validation of dynamic exhaust models for reactor design and control.
The injection of high-power electron cyclotron (EC) waves is an important actuator for locally energising the plasma in magnetic fusion devices. The injection of these multiple megawatts of EC beams provides a crucial method to precisely deposit the beam power at a desired location inside the plasma, enabling the control of magnetohydrodynamic (MHD) instabilities. However, the effect of thermal deformations of the optical components used to direct the EC beams to their target is still underexplored. To fill this gap, this work presents a test framework for linking thermally induced deformations to optical performance indicators, via a Ray Heated (RH) Structural Thermal Optical Performance (STOP) simulation structure. The applicability of this test framework is demonstrated on a former design of the first mirror of the ITER Upper Launcher (UL) and on a Defeatured Multi-Mirror (DMM) setup based on the UL mirror assembly. The results of the complete RH-STOP modelling approach show an average injection angle error of 0.07o and 0.14o for the old LM1 and DMM case studies, respectively. In addition, the DMM’s focal point is changed to a focal ring with a rough diameter of 3cm. The results show that the optical performance indicators of a high-power EC system can be significantly affected by both global and local thermal deformation. Moreover, the test framework itself aids in the localisation of the main sources of optical misalignment.