27 April 2020 in IEEE Transactions on Power Electronics
1 July 2020 in IEEE Transactions on Power Electronics
2 September 2019 in IEEE Transactions on Power Electronics
In this letter, we present a new measurement technique to evaluate the large-signal output capacitance ( $C_{\text{OSS}}$ ) of transistors as well as the $C_{\text{OSS}}$ energy dissipation ( $E_{\text{DISS}}$ ), based on the nonlinear resonance between a known inductor and the output capacitance of the device under test. The method is simple and robust, and only requires a single voltage measurement to extract the large-signal $C_{\text{OSS}}$ both in charging and discharging transients. By changing the circuit parameters, it is possible to tune the resonance frequency (even above 40 MHz) and the voltage swing (even above 1 kV) with dv/dt exceeding 100 V/ns, even though the method relies only on a low-voltage DC source, without the need for high-voltage RF amplifiers. The single-pulse operation of the method enables measuring $C_{\text{OSS}}$ and $E_{\text{DISS}}$ at very high frequency and dv/dt values without any thermal runaway. Using the proposed method, we extracted large-signal $C_{\text{OSS}}$ and $E_{\text{DISS}}$ of power transistors based on different semiconductor technologies. The obtained results were verified by Sawyer-Tower method and data reported in the literature. The precise characterization of large-signal $C_{\text{OSS}}$ of transistors presented in this letter is essential for the design of power converters, especially those operating at high switching frequencies.
6 December 2019 in IEEE Transactions on Power Electronics
The low ON-resistance of wide-band-gap (WBG) transistors is a key feature for efficient power converters, however, the anomalous loss in their output capacitance (COSS) severely limits their performance at high switching frequencies. Characterizing COSS-losses based on large-signal measurement methods requires an extensive effort, as separate measurements are needed at different operation points, including voltage-swing, frequency, and dv/dt. Furthermore, there is a practical trade-off in the maximum voltage and frequency applied to the device. In this letter we present a small-signal model to extract large-signal COSS-losses in WBG transistors. The charging/discharging COSS energy dissipation (EDISS) is presented as a function of effective COSS, series resistance RS, and switching-time tSW. Contrary to other methods, this technique directly leads to a general identification of COSS-losses at different operation points, revealing new insights on COSS-losses in WBG transistors, especially the dependence of EDISS on voltage and frequency. Based on the proposed approach, the issue of COSS-losses in enhancement-mode GaN and SiC transistors was assigned to the limited quality-factor of COSS. The precise characterization of COSS-losses proposed in this letter is essential for designing efficient high-frequency power converters.
25 November 2021 in IEEE Transactions on Power Electronics
For certain field-effect transistors (FETs) in soft-switching operation, the large-signal behavior of their output capacitance ( ${C}_\text{o}$ ) has shown to deviate considerably from the datasheet values. This can have a significant effect on hard-switching losses if the value of output charge is also different for a given voltage. In addition, standard hard-switching tests are incapable of fully setting apart the contributions from ${C}_\text{o}$ , whereas existing methods tailored to characterize ${C}_\text{o}$ losses in soft-switching operations subject ${C}_\text{o}$ to a fundamentally different charge–discharge process, and hence, might not predict the correct behavior for hard switching. To address this, first, we analyze and establish the particular charge–discharge conditions that ${C}_\text{o}$ undergoes in hard-switching circuits by considering a half bridge at no-load conditions. We show that the channel of the switching device incurs a fixed energy loss during the turn- on process, which is separated into co-energy and stored energy components of the top (complementary) and bottom (switching) devices, respectively. Exploiting this, a new measurement technique is developed to obtain output-charge versus voltage curves of devices subjected to actual hard switching. The experimental results for commercial Si, SiC, and GaN devices indicate that the effective charge-capacity of ${C}_\text{o}$ for hard switching can considerably vary from the values based on datasheets or Sawyer–Tower circuit; this could greatly undermine efficiency and thermal optimizations in the design phase of power converters.