11 July 2023 in IEEE Transactions on Biomedical Engineering
The human subcutaneous fat layer, skin and muscle together act as a waveguide for microwave transmissions and provide a low-loss communication medium for implantable and wearable body area networks (BAN). In this work, fat-intrabody communication (Fat-IBC) as a human body-centric wireless communication link is explored. To reach a target 64 Mb/s inbody communication, wireless LAN in the 2.4 GHz band was tested using low-cost Raspberry Pi single-board computers. The link was characterized using scattering parameters, bit error rate (BER) for different modulation schemes, and IEEE 802.11n wireless communication using inbody (implanted) and onbody (on the skin) antenna combinations. The human body was emulated by phantoms of different lengths. All measurements were done in a shielded chamber to isolate the phantoms from external interference and to suppress unwanted transmission paths. The BER measurements show that, except when using dual on-body antennas with longer phantoms, the Fat-IBC link is very linear and can handle modulations as complex as 512-QAM without any significant degradation of the BER. For all antenna combinations and phantoms lengths, link speeds of 92 Mb/s were achieved using 40 MHz bandwidth provided by the IEEE 802.11n standard in the 2.4 GHz band. This speed is most likely limited by the used radio circuits, not the Fat-IBC link. The results show that Fat-IBC, using low-cost off-the-shelf hardware and established IEEE 802.11 wireless communication, can achieve high-speed data communication within the body. The obtained data rate is among the fastest measured with intrabody communication.
30 March 2020 in IEEE Sensors Letters
A CMOS sensor chip was used together with an Arduino microcontroller to create and verify a low-power low-cost optical motion detector for use with traffic detection in dark and daylight conditions. The chip can sense object features with very high dynamic range. On-chip Near Sensor Image Processing (NSIP) was used to reduce the data to be transferred to a host computer. A method using local extrema points (LEP) detection was used to estimate motion through time-to-impact (TTI). Sensor data from the headlights of an approaching/passing car was used to extract TTI values similar to estimations from distance and speed of the object. The method can be used for detection of approaching objects to switch on streetlights (dark conditions) or sensors for traffic lights instead of magnetic sensors in the streets or conventional cameras (dark and daylight conditions). A sensor with a microcontroller operating at low clock frequency will consume less than 30 mW in this application.
24 October 2017 in IEEE Transactions on Circuits and Systems II: Express Briefs
An all-digital pulse width modulated (PWM) transmitter using outphasing is proposed. The transmitter uses PWM to encode the amplitude, and outphasing for enhanced phase control. In this way, the phase resolution of the transmitter is doubled. The proposed scheme was implemented using Stratix IV FGPA and class-D PAs fabricated in a 130 nm standard CMOS. From the measurement results, a spectral performance improvement is observed due to the enhanced phase resolution. As compared to an all-digital polar PWM transmitter (P-PWM), the EVM for proposed transmitter is reduced by 4.1 % and the ACLR shows an improvement of 5.6 dB for a 1.4 MHz LTE up-link signal for a carrier frequency of 700 MHz at the saturated output power of 25 dBm.
24 September 2021 in IEEE Sensors Letters
To further develop a low-power low-cost optical motion detector for use with traffic detection under dark and daylight conditions, we have developed and verified a procedure to use a Near Sensor Image Processing (NSIP) programmable 2-D optical sensor in a "1-D mode" to achieve the effect of using a cylindrical lens, thus improving the angle-of-view (AOV), the sensitivity, and usefulness of the sensor. Using an existing 256 x 256 element sensor in an innovative way, the AOV was increased from 0.4 to 21.3 in the vertical direction while also improving the sensitivity. The details of the sensor hardware architecture are described in detail and pseudo code for programming the sensor is discussed. The results were used to demonstrate the extraction of Local Extreme Points (LEPs) used for Time-To-Impact (TTI) calculations to estimate the speed of an approaching vehicle.