11 July 2023 in IEEE Transactions on Biomedical Engineering
The human subcutaneous fat layer, skin and muscle together act as a waveguide for microwave transmissions and provide a low-loss communication medium for implantable and wearable body area networks (BAN). In this work, fat-intrabody communication (Fat-IBC) as a human body-centric wireless communication link is explored. To reach a target 64 Mb/s inbody communication, wireless LAN in the 2.4 GHz band was tested using low-cost Raspberry Pi single-board computers. The link was characterized using scattering parameters, bit error rate (BER) for different modulation schemes, and IEEE 802.11n wireless communication using inbody (implanted) and onbody (on the skin) antenna combinations. The human body was emulated by phantoms of different lengths. All measurements were done in a shielded chamber to isolate the phantoms from external interference and to suppress unwanted transmission paths. The BER measurements show that, except when using dual on-body antennas with longer phantoms, the Fat-IBC link is very linear and can handle modulations as complex as 512-QAM without any significant degradation of the BER. For all antenna combinations and phantoms lengths, link speeds of 92 Mb/s were achieved using 40 MHz bandwidth provided by the IEEE 802.11n standard in the 2.4 GHz band. This speed is most likely limited by the used radio circuits, not the Fat-IBC link. The results show that Fat-IBC, using low-cost off-the-shelf hardware and established IEEE 802.11 wireless communication, can achieve high-speed data communication within the body. The obtained data rate is among the fastest measured with intrabody communication.
13 October 2025 in IEEE Transactions on Biomedical Engineering
In this article, the design of a non-invasive wearable antenna-based fat intra-body communication (Fat-IBC) system is presented for biomedical applications. The Fat-IBC system is used for uninterrupted communication between various wearable, implanted, and semi-implanted devices, facilitating the exchange of data and information within body area networks (BAN). Herein, to eliminate the design complexity, a simple planar-loop antenna is considered to establish the Fat-IBC link. For the numerical analysis, a three-layer human body tissue model (skin, fat, and muscle) is considered to optimize the antenna. A polydimethylsiloxane (PDMS) coating layer is deposited around the wearable antenna to eliminate direct contact with the human body. In addition, the antenna has also been shielded by a ferrite substrate and copper tape to reduce the loss of energy in undesired directions and stop the surface wave propagation over the skin tissue. The Fat-IBC system is constructed by using two identical wearable antennas that act as transmitting (Tx) and receiving (Rx) elements. These antennas have been placed on the three-layer human body tissue models at different distances to demonstrate the data transmission. The concept of the proposed wearable antenna-based Fat-IBC system has been established by numerical simulations and validated by experimental studies using phantoms. The proposed data transmission link was characterized using scattering parameters and the IEEE 802.11n wireless communication standard with combinations of on-skin wearable antennas. To achieve high in-body data rate using on-body antennas through the fat layer, a wireless LAN at the 2.4 GHz band was tested using low-cost Raspberry Pi single-board computers. The phantoms are utilized for measurement purposes to emulate the human body. For the proposed Fat-IBC system, a maximum link speed of 93 Mb/s is achieved using the 40 MHz bandwidth provided by the IEEE 802.11n standard at the frequency of 2.4 GHz. The obtained results demonstrate that the proposed Fat-IBC system, utilizing low-cost off-the-shelf hardware and established IEEE 802.11 wireless communication, can achieve high-speed data communication through three-layer phantom tissue.
27 February 2025 in IEEE Sensors Journal
This article introduces a detailed analysis about the effect of shielding on the performance of a resonating antenna-based wearable fat intra-body communication (Fat-IBC) system for biotelemetry applications. The Fat-IBC wearable antenna resonator is designed using a planar circular spiral resonator with a notch excited by a loop antenna. The resonator is optimized on a three-layer human body tissue model (skin, fat, and muscle) by numerical studies. A polydimethylsiloxane (PDMS) coating surrounds the resonator to prevent direct contact with the body. Further, ferrite substrate and copper tapes are used to construct a low profile shielding over the PDMS-coated wearable resonator to minimize undesired energy loss and surface wave propagation over the skin tissue. The Fat-IBC system is constructed with two identical antenna resonators acting as transmitting (Tx) and receiving (Rx) elements, placed at varying distances on the skin layer to demonstrate data transmission. The concept of the proposed Fat-IBC system has been validated through numerical simulations and experimental studies for shielded and unshielded configurations with a three-layer phantom model. The data transmission link was characterized using scattering parameters and the IEEE 802.11n wireless communication standard. The measurement study shows the transmission coefficient for shielded antennas of about –42.5 dB and –52.41 dB, while –40.91 dB and –51.13 dB were achieved from unshielded antennas at distances of 10 cm and 20 cm, respectively. Moreover, using low-cost Raspberry Pi single-board computers and the 40 MHz bandwidth provided by the IEEE 802.11n standard, the Fat-IBC system achieved a maximum link speed of 92.4 Mb/s through phantom with shielded resonator, while 79.6 Mb/s for unshielded configuration. The result obtained from the measurements establishes the feasibility of the proposed Fat- IBC system based on resonating antennas and shows the importance of shielding.