28 January 2020 in IEEE Transactions on Microwave Theory and Techniques
Mushroom-type electromagnetic bandgap (EBG) structures are known to operate as high-impedance surfaces at low-frequency bands. They are broadly used in the microwave regime. However, one of the main drawbacks of mushroom-type EBG structures is their narrow bandwidth. In this article, we propose a mushroom-type EBG structure with glide-symmetric edge vias to increase the operational bandwidth. This bandwidth increment is explained by the physical insight provided by an equivalent circuit model of the structure as well as the description of the field behavior. Simulation and measurement results show an improvement of approximately 67% over the case without glide symmetry in the structure. We conclude that applying glide symmetry to the mushroom-type EBG structures can improve their bandwidth without adding additional manufacturing costs.
1 December 2021 in IEEE Transactions on Microwave Theory and Techniques
In this article, we present a novel application of glide symmetry to differential lines with common-mode (CM) rejection filter properties. Two different topologies are investigated. First, glide symmetry is applied to a pair of differential lines where ground-connected mushrooms are employed as a CM rejection structure. The same idea is also used in a pair of differential lines where defective ground structures are introduced to stop the CM propagation. It is demonstrated that the CM rejection bandwidth is drastically increased when glide symmetry is exploited in both topologies when compared with their corresponding structures without glide symmetry. Furthermore, we show that the differential-mode propagation is hardly affected by the use of glide symmetry, ensuring the good integrity of the transmitted information. Experimental demonstration for both mushroom and defected ground structure is provided. Good agreement between simulations and measurements results is observed.
26 May 2025 in IEEE Communications Standards Magazine
Zero-energy devices, also known as Ambient power-enabled Internet of Things (A-IoT) devices, rely on harvesting ambient energy to operate. These self-sustainable devices do not need manual battery recharging or replacement, making them easy to maintain. A-IoT can address new Internet of Things (IoT) use cases within the cellular ecosystem which the existing cellular IoT technologies were not designed for. To address these use cases, a technical study was conducted by the Third Generation Partnership Project (3GPP) in Release 19 to identify the challenges and develop solutions for a new cellular radio access technology for A-IoT devices that can be deployed in 5G New Radio (NR) spectrum using or coexisting with existing NR network infrastructure. The key challenges for cellular A-IoT devices include low power budget, intermittent energy availability, limited synchronization and computational capabilities due to simplified hardware, and coexistence with NR. In this paper, the 3GPP standardization work on A-IoT is reviewed, with a focus on the physical layer aspects considered in the aforementioned Release 19 study. First, the nomenclature for A-IoT device types, architectures, and deployment scenarios is summarized. This is complemented by a description of the A-IoT physical layer design for downlink and uplink, including aspects such as physical channels, waveform, modulation, coding, preamble, and multiple access. The issues related to coexistence of A-IoT and NR are also outlined. A brief discussion on the upcoming 3GPP A-IoT standardization work concludes the paper.
26 February 2020 in IEEE Transactions on Wireless Communications
In this paper, we study optimization of multi-tone signals for wireless power transfer (WPT) systems. We investigate different non-linear energy harvesting models. Two of them are adopted to optimize the multi-tone signal according to the channel state information available at the transmitter. We show that a second-order polynomial curve-fitting model can be utilized to optimize the multi-tone signal for any RF energy harvester design. We consider both single-antenna and multi-antenna WPT systems. In-band co-existing communication links are also considered in this work by imposing a constraint on the received power at the nearby information receiver to prevent its RF front end from saturation. We emphasize the importance of imposing such constraint by explaining how inter-modulation products, due to saturation, can cause high interference at the information receiver in the case of multi-tone signals. The multi-tone optimization problem is formulated as a non-convex linearly constrained quadratic program. Two globally optimal solution approaches using mixed-integer linear programming and finite branch-and-bound techniques are proposed to solve the problem. The achieved improvement resulting from applying both solution methods to the multi-tone optimization problem is highlighted through simulations and comparisons with other solutions existing in the literature.
4 March 2022 in IEEE Internet of Things Journal
Power consumption is a major challenge for massive deployment of wireless sensors in internet of things (IoT) networks. This paper studies the use of analog joint source-channel (AJSCC) mappings in low-power sensing schemes. In particular, we propose a novel triangular mapping geometry as a low-complexity dimension reduction mapping. The proposed triangular mapping is employed for analog compression of multiple sensor readings into one signal, and thus, limits the need for power-hungry analog-to-digital conversion and processing at the sensing nodes. A comprehensive performance analysis of the proposed triangular mapping in terms of the mean squared error (MSE) performance is provided analytically and verified numerically. The problem of mapping adaptation to different source distributions is also studied. Moreover, the proposed triangular mapping is adopted in an energy scheduling problem in which the sensing nodes schedule their use of the received powers at different time instants and adjust the mapping parameters accordingly with the goal of minimizing the sum distortion at the receiver. We present a fast low-complexity algorithm for optimal energy scheduling and verify its performance in comparison with commercial convex optimization solvers. It is shown that the proposed mapping provides a very good MSE performance compared to the AJSCC benchmarks despite having a much lower complexity circuit implementation.