Tuomas Riipinen

Tuomas Riipinen

Auto-generated profile, based on publicly available information

Tuomas Riipinen

VTT Technical Research Centre of Finland Ltd., Espoo, Finland

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 May 2019 in Rapid Prototyping Journal
Verified
Journal Article
Open access
TRTuomas Riipinen
Tuomas Riipinen
SMSini Metsä-Kortelainen
Sini Metsä-Kortelainen
TLTomi Lindroos
Tomi Lindroos
Janne KeränenJanne Keränen
Janne Keränen
AMAino Manninen
Aino Manninen
JPJenni Pippuri-Mäkeläinen
Jenni Pippuri-Mäkeläinen
Purpose: The purpose of this paper is to report on the developments in manufacturing soft magnetic materials using laser powder bed fusion (L-PBF). Design/methodology/approach: Ternary soft magnetic Fe-49Co-2V powder was produced by gas atomization and used in an L-PBF machine to produce samples for material characterization. The L-PBF process parameters were optimized for the material, using a design of experiments approach. The printed samples were exposed to different heat treatment cycles to improve the magnetic properties. The magnetic properties were measured with quasi-static direct current and alternating current measurements at different frequencies and magnetic flux densities. The mechanical properties were characterized with tensile tests. Electrical resistivity of the material was measured. Findings: The optimized L-PBF process parameters resulted in very low porosity. The magnetic properties improved greatly after the heat treatments because of changes in microstructure. Based on the quasi-static DC measurement results, one of the heat treatment cycles led to magnetic saturation, permeability and coercivity values comparable to a commercial Fe-Co-V alloy. The other heat treatments resulted in abnormal grain growth and poor magnetic performance. The AC measurement results showed that the magnetic losses were relatively high in the samples owing to formation of eddy currents. Research limitations/implications: The influence of L-PBF process parameters on the microstructure was not investigated; hence, understanding the relationship between process parameters, heat treatments and magnetic properties would require more research. Originality/value: The relationship between microstructure, chemical composition, heat treatments, resistivity and magnetic/mechanical properties of L-PBF processed Fe-Co-V alloy has not been reported previously.

10 February 2023 in Corrosion Science
Verified
Journal Article
Open access
Zaiqing QueZaiqing Que
Zaiqing Que
TRTuomas Riipinen
Tuomas Riipinen
SGSneha Goel
Sneha Goel
ARAlejandro Revuelta
Alejandro Revuelta
TSTimo Saario
Timo Saario
ATAki Toivonen
Aki Toivonen

1 November 2022 in IEEE Access
Verified
Journal Article
Open access
AMAino Manninen
Aino Manninen
JPJenni Pippuri-Mäkeläinen
Jenni Pippuri-Mäkeläinen
TRTuomas Riipinen
Tuomas Riipinen
TLTomi Lindroos
Tomi Lindroos
SMSini Metsä-Kortelainen
Sini Metsä-Kortelainen
AAAtte Antikainen
Atte Antikainen
We study the use of topology optimization in the design of low-loss ferromagnetic core structures for additively manufactured electrical machines. The test case was a simple toroid core with a primary and a secondary winding. A 2D axisymmetric finite element method model was implemented for the toroid, and the core topology was optimized for minimum losses and maximum secondary flux linkage. The optimized core was then modified for additive manufacturing, and test samples were built via laser powder bed fusion. The B-H characteristics and losses of the core were measured in several operation points. The losses were compared against an additively manufactured solid core, a laminated core, and an additively manufactured core with evenly placed air gaps (i.e., grooves). The results show that the losses in the topology-optimized core are on the same level as the losses in the laminated core and considerably smaller than those in the solid core, which is a considerable improvement to previous published works.


15 June 2023 in Materials Today Communications
Verified
Journal Article
Open access
TRTuomas Riipinen
Tuomas Riipinen
JPJenni Pippuri-Mäkeläinen
Jenni Pippuri-Mäkeläinen
ZQZaiqing Que
Zaiqing Que
SMSini Metsä-Kortelainen
Sini Metsä-Kortelainen
AAAtte Antikainen
Atte Antikainen
TLTomi Lindroos
Tomi Lindroos

15 June 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
TVTimo Veijola
Timo Veijola
TRTuomas Riipinen
Tuomas Riipinen
Zaiqing QueZaiqing Que
Zaiqing Que
ARAlejandro Revuelta
Alejandro Revuelta
Experimental validation is needed to qualify additively manufactured components into safety critical applications in the nuclear industry. The benefits of additive manufacturing are usually realized in complex geometries with internal structures. However, complex geometries are more prone to manufacturing induced defects and internal features have limited surface finishing options. Extracting standard form factor specimens from such components might be impossible or remove the features most likely to cause failure. In this study a Charpy impact size-scale fatigue specimen is designed and investigated as a quality control specimen. The resulting geometry contains various print angles and is loaded through bending with constant load (R = -1). The geometry stresses and strains are evaluated using Finite Element Method (FEM) (Abaqus 2024). The FEM model is validated through comparison to physical measurements and Digital Image Correlation (DIC). The experimental fatigue results are compared to reference wrought material and strain-controlled ASTM E606 standard procedure results. The surface region of an as printed surface was the most susceptible to fatigue crack initiation and growth. All the printed specimens failed from the overhang print-side, indicating a higher susceptibility to fatigue crack initiation. The standard specimens exhibited fatigue life in line with the reference material with narrower scatter. The study cannot definitively exclude possible fixture effects from the results. The control of strain and stress in the specimen print region of interest through adjusting curvature is demonstrated through the match between the DIC and deflection gauge measurements and the FEM model.