Atte Antikainen

Mr. Atte Antikainen

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 January 2023 in Additive Manufacturing
Verified
Journal Article
Open access
OTOlivier Tosoni
Olivier Tosoni
EMElisa Borges Mendonça
Elisa Borges Mendonça
JRJoni Reijonen
Joni Reijonen
AAAtte Antikainen
Atte Antikainen
LSLukas Schäfer
Lukas Schäfer
OGOliver Gutfleisch
Oliver Gutfleisch

1 November 2022 in IEEE Access
Verified
Journal Article
Open access
AMAino Manninen
Aino Manninen
JPJenni Pippuri-Mäkeläinen
Jenni Pippuri-Mäkeläinen
TRTuomas Riipinen
Tuomas Riipinen
TLTomi Lindroos
Tomi Lindroos
SMSini Metsä-Kortelainen
Sini Metsä-Kortelainen
AAAtte Antikainen
Atte Antikainen
We study the use of topology optimization in the design of low-loss ferromagnetic core structures for additively manufactured electrical machines. The test case was a simple toroid core with a primary and a secondary winding. A 2D axisymmetric finite element method model was implemented for the toroid, and the core topology was optimized for minimum losses and maximum secondary flux linkage. The optimized core was then modified for additive manufacturing, and test samples were built via laser powder bed fusion. The B-H characteristics and losses of the core were measured in several operation points. The losses were compared against an additively manufactured solid core, a laminated core, and an additively manufactured core with evenly placed air gaps (i.e., grooves). The results show that the losses in the topology-optimized core are on the same level as the losses in the laminated core and considerably smaller than those in the solid core, which is a considerable improvement to previous published works.

4 April 2022 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
AAAtte Antikainen
Atte Antikainen
JRJoni Reijonen
Joni Reijonen
JLJuha Lagerbom
Juha Lagerbom
MLMatti Lindroos
Matti Lindroos
TPTatu Pinomaa
Tatu Pinomaa
TLTomi Lindroos
Tomi Lindroos
Nearly all commercially available alloys have been developed for manufacturing processes other than additive manufacturing. Most of those alloys are not suitable for laser powder bed fusion (L-PBF) processing due to the non-weldable nature of the alloys developed for casting, forging, and machining. Even some weldable alloys can be difficult to produce with L-PBF because the characteristics of L-PBF, such as highly concentrated heat input and the extremely high cooling rate, can lead to very high residual stresses and cracking. In order to speed up the development process of new alloys for additive manufacturing, a powder-free evaluation method was used to evaluate the materials processing window and susceptibility to cracking. Single tracks were scanned with an L-PBF machine onto H13 steel substrates. The substrate condition was varied, and its effect on melt pool geometry and cracking behavior was evaluated. The results clearly show that thermal history of the substrate influences its thermal conductivity, affecting melt pool volume. Melting point of the substrate was not found as significant factor as thermal conductivity on melt pool dimensions. Cracking type was noted to differ between substrates. If printability is assessed without powder, the substrate microstructure should be similar to rapidly solidified material. It is recognized that single-track tests are not adequate in terms of residual stress evaluation, but they can give valuable information about materials’ melting, segregation, and micro-scale cracking behavior.

21 February 2026 in Fuel
Verified
Journal Article
Open access
SOSofia Ojasalo
Sofia Ojasalo
AAAtte Antikainen
Atte Antikainen
SNSupriya Nandy
Supriya Nandy
VNVerner Nurmi
Verner Nurmi
MBMartin Bojinov
Martin Bojinov
EHElina Huttunen-Saarivirta
Elina Huttunen-Saarivirta

5 November 2022 in Metals
Verified
Journal Article
Open access
PDF file
AAAtte Antikainen
Atte Antikainen
JRJoni Reijonen
Joni Reijonen
JLJuha Lagerbom
Juha Lagerbom
MLMatti Lindroos
Matti Lindroos
Tatu PinomaaTatu Pinomaa
Tatu Pinomaa
TLTomi Lindroos
Tomi Lindroos
Laser powder bed fusion is an additive manufacturing method that is based on melting and solidification of powder material. Due to the local heating above the melting point, thermal stresses are usually formed in the final part. Mitigation of residual stresses is usually assessed by laser scan strategies and not by alloy tailoring. In this paper a segregation-based residual stress formation mechanism is proposed and assessed computationally. Additionally, an experimental setup for rapid screening of residual stress formation in various alloys is proposed. The results should ease material development of metal alloys tailored for additive manufacturing by allowing the comparison of residual stress formation tendency (e.g., solid state shrinkage) between alloys. The proposed computational method is comparative in nature and forecasting absolute residual stress values would require known temperature dependent elastoplastic properties for the alloys as well as exact thermal history. The proposed experimental method is quantitative but its reliability depends on material properties such as yield strength.

15 September 2023
Verified
Conference Paper
Closed access
TLT. Lindroos
T. Lindroos
JPJenni Pippuri-Mäkeläinen
Jenni Pippuri-Mäkeläinen
TKT. Kinos
T. Kinos
AAAtte Antikainen
Atte Antikainen
TRT. Riipinen
T. Riipinen
JOJ. O. Odden
J. O. Odden
Green electrification is vital for the society’s decarbonization. This sets a strong pressure on manufacturers of electric machines to produce items of higher efficiency and, simultaneously, prepare oneself for forecasted supply risks of raw materials. Additive Manufacturing (AM) is seen as enabler to produce components for novel electric machine architectures with designs and performance unattainable with conventional manufacturing. In this study, a permanent magnet (PM) assisted synchronous reluctance motor based on laser powder bed fusion (L-PBF) AM is introduced. Production of soft magnetic powder tailored for L-PBF and optimization of process parameters and further post treatments to achieve good magnetic properties are shown. Characterized magnetic properties are used as input values for motor design where both performance and possibilities of L-PBF are used as design criteria. Permanent Magnet electric motor of the e-scoot is used as reference. The results show that optimized architectures provide high performance with lower PM content.