Aino Manninen

Aino Manninen

Auto-generated profile, based on publicly available information

Aino Manninen

VTT Technical Research Centre of Finland Ltd., Espoo, Finland

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 May 2019 in Rapid Prototyping Journal
Verified
Journal Article
Open access
TRTuomas Riipinen
Tuomas Riipinen
SMSini Metsä-Kortelainen
Sini Metsä-Kortelainen
TLTomi Lindroos
Tomi Lindroos
Janne KeränenJanne Keränen
Janne Keränen
AMAino Manninen
Aino Manninen
JPJenni Pippuri-Mäkeläinen
Jenni Pippuri-Mäkeläinen
Purpose: The purpose of this paper is to report on the developments in manufacturing soft magnetic materials using laser powder bed fusion (L-PBF). Design/methodology/approach: Ternary soft magnetic Fe-49Co-2V powder was produced by gas atomization and used in an L-PBF machine to produce samples for material characterization. The L-PBF process parameters were optimized for the material, using a design of experiments approach. The printed samples were exposed to different heat treatment cycles to improve the magnetic properties. The magnetic properties were measured with quasi-static direct current and alternating current measurements at different frequencies and magnetic flux densities. The mechanical properties were characterized with tensile tests. Electrical resistivity of the material was measured. Findings: The optimized L-PBF process parameters resulted in very low porosity. The magnetic properties improved greatly after the heat treatments because of changes in microstructure. Based on the quasi-static DC measurement results, one of the heat treatment cycles led to magnetic saturation, permeability and coercivity values comparable to a commercial Fe-Co-V alloy. The other heat treatments resulted in abnormal grain growth and poor magnetic performance. The AC measurement results showed that the magnetic losses were relatively high in the samples owing to formation of eddy currents. Research limitations/implications: The influence of L-PBF process parameters on the microstructure was not investigated; hence, understanding the relationship between process parameters, heat treatments and magnetic properties would require more research. Originality/value: The relationship between microstructure, chemical composition, heat treatments, resistivity and magnetic/mechanical properties of L-PBF processed Fe-Co-V alloy has not been reported previously.

1 November 2022 in IEEE Access
Verified
Journal Article
Open access
AMAino Manninen
Aino Manninen
JPJenni Pippuri-Mäkeläinen
Jenni Pippuri-Mäkeläinen
TRTuomas Riipinen
Tuomas Riipinen
TLTomi Lindroos
Tomi Lindroos
SMSini Metsä-Kortelainen
Sini Metsä-Kortelainen
AAAtte Antikainen
Atte Antikainen
We study the use of topology optimization in the design of low-loss ferromagnetic core structures for additively manufactured electrical machines. The test case was a simple toroid core with a primary and a secondary winding. A 2D axisymmetric finite element method model was implemented for the toroid, and the core topology was optimized for minimum losses and maximum secondary flux linkage. The optimized core was then modified for additive manufacturing, and test samples were built via laser powder bed fusion. The B-H characteristics and losses of the core were measured in several operation points. The losses were compared against an additively manufactured solid core, a laminated core, and an additively manufactured core with evenly placed air gaps (i.e., grooves). The results show that the losses in the topology-optimized core are on the same level as the losses in the laminated core and considerably smaller than those in the solid core, which is a considerable improvement to previous published works.

21 September 2021 in Environmental Research Letters
Verified
Journal Article
Open access
PDF file
SJSamppa Jenu
Samppa Jenu
BSBau­meis­ter Ste­fan
Bau­meis­ter Ste­fan
JPJenni Pippuri-Mäkeläinen
Jenni Pippuri-Mäkeläinen
AMAino Manninen
Aino Manninen
MPMarko Paakkinen
Marko Paakkinen
The transportation sector has become the fastest growing source of greenhouse gas (GHG) emissions. One solution to mitigate the impacts is a shift towards electric modes. Where previous studies have only focused on the replacement of individual modes, our study presents a more holistic approach by comparing land-based, water-based and airborne transportation modes. We study the GHG emission reduction potentials of electric cars, buses, trains, ferries and aircraft in comparison to existing modes on 34 routes within Finland and across the Baltic Sea to Sweden and Estonia. By comparing the GHG emissions in carbon dioxide equivalents (CO2-eq) per passenger kilometer for each mode, we also consider the emissions generated from battery production as well as the differences in the energy mix from electricity production of the three studied countries. In addition to CO2-eq emissions per passenger kilometer, we also take real door-to-door travel times into account. Our study found that electric transportation modes possess great potential for emissions reduction. Nevertheless, depending on the energy mix used for electricity production, the emissions of electric transportation modes can exceed those of existing modes significantly. In addition, the emissions generated by battery production can have a significant share of the total emissions and should therefore always be considered. Finally, while also taking into account the door-to-door travel times, our study identified the great potential of electric aircraft to provide a less carbon intensive transportation option paired with short travel times starting on routes beyond 300 km where no high-speed rail exists as well as on routes across the water.

15 September 2023
Verified
Conference Paper
Closed access
TLT. Lindroos
T. Lindroos
JPJenni Pippuri-Mäkeläinen
Jenni Pippuri-Mäkeläinen
TKT. Kinos
T. Kinos
AAAtte Antikainen
Atte Antikainen
TRT. Riipinen
T. Riipinen
JOJ. O. Odden
J. O. Odden
Green electrification is vital for the society’s decarbonization. This sets a strong pressure on manufacturers of electric machines to produce items of higher efficiency and, simultaneously, prepare oneself for forecasted supply risks of raw materials. Additive Manufacturing (AM) is seen as enabler to produce components for novel electric machine architectures with designs and performance unattainable with conventional manufacturing. In this study, a permanent magnet (PM) assisted synchronous reluctance motor based on laser powder bed fusion (L-PBF) AM is introduced. Production of soft magnetic powder tailored for L-PBF and optimization of process parameters and further post treatments to achieve good magnetic properties are shown. Characterized magnetic properties are used as input values for motor design where both performance and possibilities of L-PBF are used as design criteria. Permanent Magnet electric motor of the e-scoot is used as reference. The results show that optimized architectures provide high performance with lower PM content.