1 September 2023 in Journal of Geotechnical and Geoenvironmental Engineering
1 October 2024 in Geosynthetics International
Field observations and centrifuge tests indicate that progressive column bending failure accompanies most instabilities of rigid-column-supported and geosynthetic-reinforced (RCGR) embankments. However, recognized guidelines specifically for evaluating the overall stability of such systems featuring bending failure remain limited. A general methodology to calculate the factor of safety (FS) for RCGR embankments using the limit equilibrium method is presented in this article. The focus is on deep-seated slope failures, wherein rigid columns progressively fracture due to subsoil overstressing. The concentric arches model, along with tensioned geosynthetic analysis, informs the determination of vertical and horizontal loads on the column heads. The column's resisting moment stems from its flexural and compression resistance. A mobilization factor for the net thrust on each column is defined to capture the progressive failure. The methodology involves an iterative computational procedure to identify the critical slip surface and the FS using the Fellenius' method. The solution was validated using three case studies, including both centrifuge models and field tests, as well as finite-element analysis. The results indicate that the soil mass contributes the most to resisting sliding and overall stability, followed by columns and geosynthetics. In addition, axial force mainly provides the resisting moment of columns.
1 June 2024 in Canadian Geotechnical Journal
Counterweight retaining walls (CRWs) are a variant of gravity-retaining walls that feature a pressure relief platform (RP) on the backfill side to reduce total earth pressure, offering a cost-effective option compared to traditional forms. However, the intricate interactions between CRWs and backfill, coupled with the lack of clear design guidelines, have restricted their use. This study examines the behavior of CRWs in translation mode using three different centrifuge model tests, each with varying fill heights. Observations show a slightly concave slip surface through the wall heel and a nearly planar slip surface extending from the edge of the RP to the back of the wall in an active limit state. Backfill movement can be classified into translation, sliding, and stable zones. Earth pressure distribution on the upper wall follows a trapezoidal pattern, whereas the pressure on the lower wall exhibits a triangular distribution. Earth pressure on the RP is approximately linear, peaking near the RP’s edge. Introducing a friction angle mobilization factor for the potential first slip surface improves accuracy in calculating earth pressure. The tests were replicated to validate the analytical model for earth pressure calculations, using the adaptive finite-element limit analysis method.
1 September 2023 in Geotechnical Testing Journal
This study develops a novel apparatus to simulate the staged, automatic construction of embankments in geotechnical centrifuges with improved measurement accuracy. Modular test equipment was designed to incorporate the functionality of controllable and precise sand release; its structural components include a box-like sand storage module, a push-pull sand release module, and a stepper motor control module. Emphasis was placed on the design of segmented deflectors, the angles of which were derived with rigorous mathematical analysis to mitigate the Coriolis effect on falling sand. Calibration tests demonstrate that the post-construction embankment geometry approximates its target shape with a relative error of 0.72 to 7.37 % in different construction phases at an acceleration of 60 g. A trial was conducted on a staged embankment over the deformable ground, and the displacement of this system was monitored and characterized by tracking reflective marker technology. The results indicate that the proposed method is effective and reflects real-life situations.
18 December 2025 in Soil Dynamics and Earthquake Engineering
1 December 2024 in Canadian Geotechnical Journal
Laterites and lateritic soils, prevalent in tropical and subtropical climates, have growing applications in earthwork construction. They usually present unique compression properties compared to conventional clays. Therefore, a thorough understanding of their intrinsic compressibility is crucial. This paper reports on modified oedometer tests conducted on reconstituted samples of four distinct laterites and lateritic soils with varying initial water contents. In addition, scanning electron microscopy (SEM) was utilized to identify the microstructural features to reveal the mechanisms of intrinsic compression. The results demonstrate that intrinsic compression curves of reconstituted laterites and lateritic soils align with Burland’s normalization framework. However, they exhibit a higher void ratio at an effective vertical stress of 100 kPa ( e* 100) and a lower compression index ( C* c) compared to traditional clays; therefore, existing formulas for calculating e* 100 and C* c are inapplicable to laterites and lateritic soils. The SEM analysis revealed that sesquioxide interacts with soil minerals, resulting in a porous structure and robust inter-unit cementation. This unique microstructure contributes to the observed intrinsic constants of compressibility, e* 100 and C* c. Based on the experimental observations, new empirical equations are introduced to evaluate e* 100 and C* c in laterites and lateritic soils. The experimental results elucidate the role of sesquioxide in inherent compressibility and improve our understanding of compressibility characteristics that are unique to laterites and lateritic soils.